Whirlpool IDPA G45 A2 ECO (EU) Instruction for Use download pdf (Page 6)

Disconnecting the power supply

! Disconnect the dryer when not in use or

during cleaning and maintenance operations.

Cleaning the filter after each cycle

The filter is a fundamental component of the

dryer: its function is to collect lint and fluff that

form during drying.

Clean the filter once

drying is completed, by

rinsing it under running

water or cleaning it with a

vacuum cleaner. Should

the filter become clog-

ged, the flow of air inside

the dryer will be seriously

hampered: drying times becomes longer and

more energy is consumed. Moreover, the dryer

may become damaged.

The filter is located in

front of the dryer seal

(see Picture).

Removing the filter:

1. Pull the filter’s plastic

handle upwards (see

Picture).

2. Clean the fluff off the

filter and replace it correctly. Ensure that the

filter is pushed fully home.

! Do not use the dryer unless the filter has

been replaced in its holder.

Checking the drum after each cycle

Rotate the drum manually to remove smaller items (handker-

chiefs) that could have been left inside the dryer.

Cleaning the drum

! Avoid using abrasives, steel wool or stainless steel cleaning

agents to clean the drum. A coloured film may appear on the

stainless steel drum surface: it may be caused by a combina-

tion of water and/or cleaning agents such as wash-softeners.

This coloured film does not affect the dryer’s performance.

Emptying the water container after each

cycle

Remove the water container and

empty it into a sink or other

suitable drain outlet, then

replace it correctly.

Always check the water contai-

ner and empty it before starting

a new drying cycle.

-Failure to empty the water container may cause the

following:

- The dryer stops heating (thus the load may still be

damp at the end of the drying cycle).

- The “Empty water container” LED activates to show

that the water container is full.

Priming the Water Collection System

When your dryer is new, the Water Container will not

collect Water until the system is primed, this will take

1 or 2 drying cycles. Once primed it will collect Water

during every cycle.

Cleaning the Heat Pump Filter Unit

• Periodically (every 5 drying cycles) remove

Heat pump filter unit and clean any build up

of fluff from the surface of the filter by rinsing

it under running water or with your vacuum

cleaner.

We however recommend that you clean this

filter after every drying cycle to optimize the

dryers performance.

To remove Heat pump

filter unit:

1. Unplug the dryer and

open the door.

2. Remove the filter unit

by rotating the 4 clips

to the vertical position

then pulling the filter

unit towards you.

3. Separate the two

parts of the filter unit and

clean the surface of the

filter.

! Warning: The front of

the heat pump is made

from thin metal plates.

Take care that you do

not damage these or cut

yourself when cleaning,

removing or replacing

the filter unit.

4.Whenever you clean

the Heat pump filter

unit always clean any

build up of fluff from

the surface of the metal

plates. Carefully clean

this fluff off with a damp

cloth,sponge or vacuum

cleaner. Never use your

Fingers.

5. Assemble the two parts of the filter clean

the surface of the seals and replace with the

4 clips into the horizontal position, sure that

the catches have been secured.

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be clea-

ned with a damp cloth.

Care and maintenance

Water container

Heat pump

filter unit

Condenser cover

Catches

Filter

Handle

Air intake

• Clean the front air intake grille regularly (every 6 months)

with a vacuum cleaner to remove any lint, fluff or dust

deposits. Furthermore, remove any lint deposits from the

front part of the condenser and from the filter area, using

a vacuum cleaner every so often.

! Do not use solvents or abrasives.

! Have the dryer checked regularly by authorised technical

personnel in order to ensure that the electrical and mechani-

cal parts work safely (see Assistance).

Quick Tips

!Remember to clean your filter and Heat

Pump filter unit after each load.

! Remember to empty your water contain-

er after each load.

! Doing this will keep your machine work-

ing at its BEST!

1 2 3 4 5 6 7 ... 80

Comments to this Manuals

No comments

Whirlpool IDPA G45 A2 ECO (EU) Instruction for Use Page 6

Comments to this Manuals

Related products and manuals for Unknown Whirlpool IDPA G45 A2 ECO (EU)