Whirlpool CGD9150GW Installation Guide download pdf (Page 29)

ELECTRONIC CONTROL SETUP INSTRUCTIONS

How to Use the Buttons to Program the Controls

1. The COTTON/WHITES button is used to adjust the values

associated with set-up codes. Pressing the button will

change the value by increments. Rapid adjustment is

possible by holding down the button.

2. The PERM PRESS button will advance through the set-up

codes. Pressing this button will advance to the next available

set-up code. Holding down the button will automatically

advance through the set-up codes at a rate faster than

1 per second.

3. The COLORS/DELICATES button is used to select

or deselect options.

Start Operating Setup

Insert service access door key, turn, and lift to remove service

access door.

Dryers with Card Reader Installed:

Once the debit card reader is installed (according to the

reader manufacturer’s instructions), the set-up mode can be

entered by inserting a manual set-up card (supplied by the

reader manufacturer) into the card slot. If manual set-up card

is not available, only the diagnostic mode can be entered by

removing the service access door.

IMPORTANT: To access set-up mode or diagnostic mode,

use a service key (9050 models) to open the service access

door. If a card reader is installed, a service card is available

for accessing diagnostics. If a service key is not available

(9060 models), the AA1 connector must be removed or

the Service Access Code described below must be used.

The console must not be opened unless power is rst

disconnected from the dryer. To access connector AA1:

1. Unplug dryer or disconnect power.

2. Open console, remove plug on AA1, and close console.

3. Plug in dryer or reconnect power.

The dryer is now in the set-up mode.

To enter the alternative Service Access Code and enter set-up

mode: Press the Left Button, Right Button, Left Button, Right

Button, and Right Button.

NOTE: It is not necessary to set up the dryer with the following

codes; the dryer is pre-set at the factory. These codes can be

used to change settings, if desired.

Set-Up Codes

■ The PERM PRESS button will advance from code to code.

■ The COTTON/WHITES button will change the code value.

■ The COLORS/DELICATES button will select or deselect

options.

The set-up code is indicated by the one or two left-hand

characters. The set-up code value is indicated by the two

or three right-hand characters.

NOTE: The rst line of each code indicates the factory default.

Code Explanation

6. 06 REGULAR CYCLE PRICE

6. 06 When the d.xx is set to d.00, this 6.xx value represents

the number of coins (coin 1) needed to start the dryer;

may adjust from 0–39. Change this value by pressing

the COTTON/WHITES button. 6.06 = 6 coins = $1.50.

(9160 models default to 6.00.)

6. 01 When the d.xx is set to d.CS, this 6.xx value

represents the number of push-in actuations of the

coin slide to start the dryer. 6.01 would equal one coin

slide activation.

• Press the PERM PRESS button once to advance

to next code.

7. 05 REGULAR DRY TIME

7. 05 When set to Coin Drop or Card Reader operation, the

dry time equals the Regular Dry Time value multiplied

by the Regular Cycle Price value. Example: 6.06 and

7.05 = (06 x 05 = 30 minutes).

7. 45 For coinslide or OPL operation, the value is the

amount of minutes of dry time. Factory default of 45

minutes. Pressing COTTON/WHITES adjusts the value

from 1–99 minutes.

• Press the PERM PRESS button once to advance

to next code.

8. 00 TYPE OF DRYER PRICING

8. 00 Fixed Cycle with Top Off. Only available for use with

coin drops or card readers. For detailed description,

see “General User Information.”

8. FC Fixed Cycle. For detailed description, see General

User Information. Use COLORS/DELICATES button

to make this selection.

• Press the PERM PRESS button once to advance

to next code.

9. 00 CYCLE COUNTER OPTION

This option is either NOT SELECTED “OFF”

or SELECTED “ON.”

9. 00 Not Selected “OFF.”

9. 0C Selected “ON” and not able to be deselected.

• Press the COLORS/DELICATES button

3 consecutive times to select “ON.” Once

selected “ON” it cannot be deselected.

• Press the PERM PRESS button once to advance

to next code.

1. 00 MONEY COUNTER OPTION

This option is either NOT SELECTED “OFF”

or SELECTED “ON.”

1. 00 Not Selected “OFF.”

1. 0C Selected “ON.”

• Press the COLORS/DELICATES button

3 consecutive times to select “ON” and 3

consecutive times to deselect (Not Selected “OFF”).

Counter resets by going from “OFF” to “ON.”

1. C0 Selected “ON” and not able to be deselected.

• To select “ON” and not able to be deselected,

rst select “ON;” then within 2 seconds press the

COLORS/DELICATES button twice, the COTTON/

WHITES button once, and exit set-up mode.

• Press the PERM PRESS button once to advance

to next code.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 63 64

Comments to this Manuals

No comments

Whirlpool CGD9150GW Installation Guide Page 29

Comments to this Manuals

Related products and manuals for Washer dryers Whirlpool CGD9150GW