Whirlpool AWM 5083 Instruction for Use download pdf (Page 12)

a. Water inlet fault (no or insufficient water supply)

For models with a fault display, the Water tap

indicator is on or the display alternately shows

FH. Switch off the appliance by turning the

programme selector to the   position and

unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:



the water tap is completely open, and the water

supply pressure is sufficient;



the water inlet hose is kinked;



the mesh filters are blocked (see Care and

Maintenance / Water Hose Mesh Filters);



the water inlet hose is frozen.

Reconnect the appliance to the electrical supply.

For models with a fault display, reselect the

desired programme and press the

Start/Pause

button again to continue with the programme (do

not add detergent for this programme).

For models without a fault display continue the

programme by pressing the

On/Off

button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see After-Sales Service).

b.Draining out fault

For models with a fault display, depending on the

model, the display shows statically or alternately

FP. Switch off the appliance by turning the

programme selector to the   position and

unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:



the drain hose is kinked (see Installation

Guide);



the pump / filter are blocked (see Removing the

Filter / Draining Residual Water);

IMPORTANT

: before draining, allow the wash water

to cool down.



the drain hose is frozen.

Connect the appliance to the electrical supply.

For models with a fault display reselect the desired

programme and press the

Start/Pause

button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the

On/Off

button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see After-Sales Service).

c. Electrical module fault

For models with a fault display F4 to F15 are

displayed and some or all Spin Speed Selection

LEDs are flashing. Switch off the appliance. Select

a programme and press the

Start/Pause

button

once again. The programme will continue.

For models without a fault display the washing

machine stops in the appropriate step. Switch the

appliance first off, then on. The programme will

continue.

If the fault re-occurs, contact After Sales Service

(See After-Sales Service).

d. Water Stop fault

(if available)

The Water Stop may have been triggered by:

too much foam.

a leak in the inlet hose or in the appliance.

In this case the pump is switched on

automatically in order to pump the water out.

For models with a fault display the light of the

Water Stop indication is on. The display shows

FA or alternately F and A and the pump is

running. Switch off the appliance by turning the

programme selector to the   position, unplug

the appliance and make sure that the water tap is

closed.

For models without a fault display the washing

machine stops in the appropriate step. Switch off

the appliance, , unplug the appliance and make

sure that the water tap is closed.

Tilt the appliance forwards carefully to allow the

collected water to flow out.

Then:

plug in the appliance,

turn the water tap on (if water immediately

flows into the appliance again, without the

appliance being started, close water supply and

call After-Sales Service).

For models with a fault display reselect the desired

programme and press the

Start/Pause

button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the

On/Off

button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see After-Sales Service).

3gb05398.fm Page 28 Monday, August 26, 2002 12:42 PM

Black process 45.0° 100.0 LPI

1 2 ... 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Whirlpool AWM 5083 Instruction for Use Page 12

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool AWM 5083