Whirlpool System II Specifications

Browse online or download Specifications for Water dispensers Whirlpool System II. Whirlpool System II Specifications User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 17
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
1
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the
whirlpool installation are your selected fittings and electrical connections.
To insure maximum performance and pleasure from this product, please follow the instructions and cautions.
MODEL 2422L / V 5' x 32"
MODEL 6060L / V CORNER
MODEL 2771L / V 5' x 36"
MODEL 2645L / V OVAL
MODEL 7236L / V 6' x 36"
MODEL 2425L / V - LHO 5' x 32" IA-LHO
MODEL 2425L / V - RHO 5' x 32" IA-RHO
MODEL 2908L REMINISCENCE
MODEL 2711L ELLISSE
MODEL 2773L CADET 6' x 36"
MODEL 2774L CADET 6' x 42"
MODEL 2775L CADET CORNER
MODEL 2732L 5' x 32"
© AS Americas Inc. 2010
All product names listed herein are trademarks
of AS Americas Inc. unless otherwise noted.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
INSTALLATION & OPERATION GUIDE FOR
EVERCLEAN
/ EVOLUTION
WHIRLPOOLS AND BATHTUBS
753737-100 Rev. E
Page view 0
1 2 3 4 5 6 ... 16 17

Summary of Contents

Page 1 - WHIRLPOOLS AND BATHTUBS

1THANK YOU...for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is

Page 2 - TABLE OF CONTENTS:

10753737-100 Rev. EINSTALLATION AND FRAMING INSTRUCTIONSThe variety of installations possible for this whirlpool may require framing procedures other

Page 3 - INSTRUCTIONS

753737-100 Rev. E11SUGGESTED WHIRLPOOL / BATH INSTALLATION METHODSECURE THE BATH TO THE STUDS AS SHOWN FOR WOOD OR STEEL STUD CONSTRUCTION. TYPICAL FL

Page 4

12753737-100 Rev. EAll wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable cod

Page 5 - SPECIFICATIONS:

753737-100 Rev. E13For 6060L/V Corner Only OPERATIONELECTRICAL CONNECTIONSInstall a separate 120VAC / 15AMP dedicated circuit with GFCI (Ground Fault

Page 6 - ROUGHING-IN REFERENCES

14753737-100 Rev. EOPERATION:NOTE: Each whirlpool is shipped from the factory with an air actuator on/off switch and pump with attached power supply

Page 7

753737-100 Rev. E15Adjustable Flow Clean Jet™: The water flow action may be adjusted from vigorous to soft by rotating the nozzle counterclockwise fo

Page 8

16753737-100 Rev. EDRAIN CONNECTION AND SYSTEM TESTUsing recommended drain assembly, connect whirlpool drain to waste line in accordance with the drai

Page 9

753737-100 Rev. E17By Mail: American Standard Inc. P.O. Box 6820 Piscataway, N.J. 08855 Attention: Customer

Page 10 - 753737-100 Rev. E

2753737-100 Rev. ETABLE OF CONTENTS:Safety Instructions...Page 3General In

Page 11 - TYPICAL INSTALLATION

753737-100 Rev. E3!!!!!!!SAVE THESE INSTRUCTIONSWARNING: Risk of personal injury. Do not permit children to use this unit without adult supervision.WA

Page 12 - 20 amp dedicated

4753737-100 Rev. EEverclean™/Evolution™ CornerEverclean™/Evolution™ 5' x 32"Everclean™/Evolution™ 5' x 36"Everclean™/Evolution™ 6&

Page 13 - E-Z INSTALL

753737-100 Rev. E5SPECIFICATIONS:GENERAL SPECIFICATIONS FOR LIFETIME / EVOLUTION WHIRLPOOLS AND BATH TUBSTABLE 1SIDE VIEWDRAIN / OVERFLOWEND VIEWLHWCA

Page 14 - OPERATION:

6753737-100 Rev. EDIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.RO

Page 15

753737-100 Rev. E7DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.CO

Page 16 - AFTERCARE and CLEANING

8753737-100 Rev. EREMINISCENCE (MODEL 2908L)229 x 305mm(9 X 12)FLOORCUTOUT64mm REF.(2-1/2)1676mm(66")PUMP914mm(36")457mm(18)330mm(13")I

Page 17

753737-100 Rev. E9ROUGHING-IN REFERENCESDIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z

Comments to this Manuals

No comments