Whirlpool W10224664A User Manual download pdf (Page 5)

5. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the ¹⁄₄" (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Refrigerator Doors

It may be necessary to remove the doors to allow the refrigerator

to pass through the doorway of your home. See the instructions

below to remove and replace the doors.

IMPORTANT:

■ The doors are not reversible.

■ Remove the entire door, not just the handles. It is more

difficult to replace the handles correctly.

■ Before you begin, turn the refrigerator control OFF. Unplug

refrigerator or disconnect power.

■ Remove food and adjustable door or utility bins from doors.

■ All graphics referenced in the following instructions are

included later in this section.

TOOLS NEEDED: ⁵⁄₁₆" hex head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench,

flat 2" putty knife.

Remove Doors and Hinges

⁵⁄₁₆

" Hex Head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the top hinge cover and the parts for the top hinge

as shown in Top Hinge graphic.

4. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

6. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Replace Doors and Hinges

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten

all screws. See Center Hinge graphic. Replace the freezer

door.

3. Assemble the parts for the top hinge as shown. Replace

spacer and hinge. Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all

screws and replace hinge cover. See Top Hinge graphic.

Final Steps

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See “Using the Control(s).”

3. Return all removable door parts to doors and food to

refrigerator.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

1 2 3 4 5

Comments to this Manuals

No comments

Whirlpool W10224664A User Manual Page 5

Comments to this Manuals

Related products and manuals for Fridges Whirlpool W10224664A