Whirlpool 9BRKPG6001A Instruction for Use download pdf (Page 3)

withthethicknessoftheworktop(seethefollowinggures).

Top 20 mm

Top 30-50 mm

ADJUSTMENT TO DIFFERENT TYPES OF GAS

This operation must be performed by a qualied technician.

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• ThegasnozzlesmustbechangedbyAfterSalesServiceoraqualiedtechnician.

• NozzlesnotsuppliedwiththeappliancemustbeorderedfromAfterSalesService.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience difculty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap

if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Instruction)

• Remove grids (A).

• Extractburners(B).

• Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to

be replaced.

• Replace it with the injector suitable for the new type of gas.

• Re-assemble the injector in (D).

• If you have a multiple crown burner use side spanner to replace the injector (E).

Beforeinstallingthehob,remembertoafxthegascalibrationplatesuppliedwiththeinjectorsin

suchawaythatitcoverstheexistinginformationrelatingtogascalibration.

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:

• tightenscrewtoreducetheameheight(-);

• loosenscrewtoincreasetheameheight(+)

Theadjustmentmustbeperformedwiththetapinminimumgassettingposition(smallame) .

• The primary air of the burners does not need to be adjusted.

• Atthisstage,lightuptheburnersandturntheknobsfrommaxposition to minimum position tocheckamestability.

Uponcompletionofadjustment,resealusingsealingwaxoranequivalentmaterial.

REFERENCE TO LOCAL REGULATIONS

Installation must be performed in accordance with standard NBN D 51-003.

AFTER-SALES SERVICE

Before calling the After-Sales Service, make sure you can give the following information:

- type of fault or problem;

- exactmodel(writtenonthelabelafxedtotheinstruction/warranty);

- servicenumberthatfollowsthewordSERVICEontheratingplateunderthehobandonthelabelafxedtoinstruction/warranty;

- your complete address and phone number.

If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty.

TROUBLESHOOTING GUIDE

If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem.

1. The burner fails to ignite or the ame is not even

Check that:

• The gas or electrical supplies are not shut off and especially that the gas supply tap is open.

• The gas cylinder (liquid gas) is not empty.

• The burner openings are not clogged.

• The plug end is not dirty.

• All the burner parts have been positioned correctly.

• There are no draughts near the hob.

WARNING

1 2 3 4 5 6 7 8 ... 23 24

Comments to this Manuals

No comments

Whirlpool 9BRKPG6001A Instruction for Use Page 3

Comments to this Manuals

Related products and manuals for Hobs Whirlpool 9BRKPG6001A