Whirlpool CHW9150GW Installation Guide download pdf (Page 10)

NOTE: After the washer has been installed and plugged in,

the display may show ‘0 MINUTES’. Once the washer has been

plugged in and the washer door opened and closed, the display

will show the price. In washers set for free cycles, the display will

ﬂash ‘SELECT CYCLE’.

1. Insert coins until ‘SELECT CYCLE’ ﬂashes in display.

2. Door must be closed before cycle selection is made,

3. Press fabric setting button for the wash cycle desired. After

the cycle is started, the time will display and count down.

4. If a cycle is interrupted by opening the door, ‘RESELECT

CYCLE’ will ﬂash in the display. To restart the washer, close

door and reselect desired cycle.

General User Information

SCROLLING ‘OUT OF ORDER’ SHOWING IN DISPLAY

This condition indicates the washer is inoperative.

‘0 MINUTES’ SHOWING IN DISPLAY

This indicates the cycle is complete and the washer cannot be

operated. Coins dropped or debit inputs during this condition will

be stored in escrow but cannot be used until normal operation is

restored by opening and closing the door. If a door switch fails,

it must be replaced before normal operation can be restored.

COLD START (Initial ﬁrst use)

Washer is programmed at the factory as follows:

11-minute wash period

3 rinses (extra rinse not enabled)

$2.00 wash price (9150 model)

$0 wash price (9160 model)

WARM START (after power failure)

A few seconds after power is restored, if a cycle was in progress

at the time of the power failure, ‘RESELECT CYCLE’ will ﬂash

in the display, indicating the need for a button press to restart

the washer.

DOOR LOCK

Prior to beginning a cycle, there is a door lock routine of lock/

unlock/relock; then the cycle begins. The door will remain locked

until the end of a cycle or approximately 2 minutes after a power

interruption.

PRICING

After the door is opened following the completion of a cycle,

the display indicates the cycle price (unless set for free operation).

As coins are dropped or debit inputs arrive, the display will change

to lead the user through the initiation of a cycle.

FREE CYCLES

This is established by setting the cycle price to zero. When this

happens, ‘SELECT CYCLE’ will appear rather than a cycle price.

DEBIT CARD READY

This washer is debit card ‘cable’ ready. It will accept a variety of

debit card systems but does NOT come with a debit card reader.

Refer to the debit card reader manufacturer for proper washer

setup. In models converted to a Generation 1 debit card system,

debit pulses represent the equivalent of one coin (coin 1).

Control Set-Up Procedures

IMPORTANT: Read all instructions before operating.

9150 Models: Insert access door key, turn, and lift to remove

access door.

9160 Models: Once the debit card reader is installed (according

to the reader manufacturer’s instructions), the set-up mode can

only be entered by inserting a set-up card (supplied by the reader

manufacturer) into the card slot. If a set-up card is not available,

diagnostic modes can be entered by removing connector AA1

on the circuit board or by using the Service Access Code (see

“Service Access Code” section, page 13) for 9160 models.

IMPORTANT: Unplug washer or disconnect power before opening

the console. To access connector AA1:

1. Unplug washer or disconnect power.

2. Open console, disconnect plug on AA1, and close console.

3. Plug in washer or reconnect power.

The washer is now in the set-up mode. The lower 3 buttons

and the digital display are used to set up the controls. The display

can contain 4 numbers and/or letters and a decimal point. These

are used to indicate the set-up codes and related code values

available for use in programming the washer.

Once the washer has been programmed with a Generation 2 card

reader installed, the washer will be in dAS mode permanently and

dAS will be displayed every time set-up mode is accessed.

The lower fabric setting buttons and the digital display are used

to set up the controls.

The display can contain 4 numbers and/or letters and a decimal

point. These are used to indicate the set-up codes and related

code values available for use in programming the washer.

HOW TO USE THE BUTTONS TO PROGRAM THE CONTROLS

1. The Hot button is used to adjust the values associated with

set-up codes. Pressing the button will change the value by

increments. Rapid adjustment is possible by holding down

the button.

2. The Warm button will advance through the set-up codes. Press-

ing the button will advance to the next available set-up code.

Holding the button down will automatically advance through the

set-up codes at a rate of 1 per second.

3. The Cold button is used to select or deselect options.

USER & SETUP INSTRUCTIONS

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Comments to this Manuals

No comments

Whirlpool CHW9150GW Installation Guide Page 10

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool CHW9150GW