6
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the
cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle
will automatically compensate by adding time, heat and water as needed.
OPTION SELECTIONS
OPTIONS DISH LOAD TYPES DESCRIPTIONS USE WITH:
Pans, casseroles,
etc. with tough food
soil.
Activates the POWERSCOUR™ spray jets and provides intensified
water spray to the back of the lower level rack.
May add heat and time to the cycle.
Adaptive Wash, Pots &
Pans or Normal cycle
To sanitize your
dishes and
glassware in
accordance with
NSF/ANSI Standard
184 for Residential
Dishwashers.
Raises the water temperature in the final rinse to approximately
155°F (68°C). This high temperature rinse sanitizes your dishes
and glassware in accordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments.
The Sanitize or Sani Rinse option adds heat and time to the cycle.
Adaptive Wash, Pots &
Pans or Normal cycle.
Only these sanitization
cycles have been
designed to meet the
NSF/ANSI requirements.
Loads containing
tough, baked-on
food.
Increases the target water temperature during the wash portions of
the cycle.
Adds heat, wash time and water to the cycle.
Adaptive Wash, Pots &
Pans or Normal cycle
For best drying
results, dry dishes
with heat.
Turn OFF when loads contain plastic dinnerware that may be
sensitive to high temperatures.
This option with the use of rinse aid will provide the best drying
performance.
All cycles, except GLASS
XPRESS™ and Rinse
Only. Automatic with all
wash cycles unless you
turn it off.
To run your dish
washer at a later
time or during off-
peak hours.
Delays the start of a cycle up to 4 hours.
Select a wash cycle and options. Press 4 Hour Delay. Press
START/RESUME. Close the door firmly.
All cycles, except Rinse
Only
Control Lock To avoid unintended
use of your
dishwasher, or cycle
and option changes
during a cycle.
To turn on Lock, press and hold Heat Dry for at least 4 seconds.
To turn off Lock, press and hold Heat Dry for at least 4 seconds.
When Control Lock is lit, all buttons are disabled. If you press any
pad while your dishwasher is locked, the light flashes 3 times. The
dishwasher door can be opened while the controls are locked.
Anytime
CONTROLS AND
CYCLE STATUS
CONTROL PURPOSE COMMENTS
To start or resume a
wash cycle
If the door is opened during a cycle or the power is interrupted, the Start/Resume indicator
flashes. The cycle will not resume until the door is closed and Start/Resume is pressed.
To cancel wash
cycle
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher
drain completely.
To follow the
progress of your
dishwasher cycle
The Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the Sani Rinse cycle is finished, the Sanitized indicator
glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required
temperature. The light goes off when you open and close the door or press CANCEL.
water not pumping out
cycle ended
Filter cleaning help
Trying to find the filter to clean it on a Quiet Partner III whirlpool dishwasher.
Soak and normal lights alternately flash. I need to reset the control panel, imo
Not work at all…help
Where is the filter on this dishwasher?
How do I clean th filter on Whirlpool Quiet Partner III?
Why is it so difficult to find & clean this filter??
Where is the filter?
How do U clean filter?
where is the filter on Quiet Partner IV?