Whirlpool 9700S User Manual download pdf (Page 22)

2-13

The following kits for close clearance alternate

nstallations are available for purchase. Please see the

“

Assistance or Service” section of this manual to order.

Over-the-Top Installation:

Part Number 4396028

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)

mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

The exhaust vent must be securely fastened to a noncombustible

ortion of the mobile home structure and must not terminate

eneath the mobile home. Terminate the exhaust vent outside.

12 324567 289 27 3 83

Select the route that will provide the straightest and most

direct path outdoors.

Plan the installation to use the fewest number of elbows and

turns.

When using elbows or making turns, allow as much room as

possible.

Bend vent gradually to avoid kinking.

Use the fewest 90° turns possible.

12 324567 289 2 7 382 7  38782    87 2 2 2 8 48 238

4678244572

Use the following Vent system chart to determine type of vent

material and hood combinations acceptable to use.

Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those

specified will:

Shorten the life of the dryer.

Reduce performance, resulting in longer drying times and

increased energy usage.

he Vent system chart provides venting requirements that will

elp to achieve the best drying performance.

273832584

Side and bottom exhaust installations have a 90º turn

inside the dryer. To determine maximum exhaust length, add one

90º turn to the chart.

73 273 325

Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible.

See ?Determine vent path? in ?Plan Vent System.? Avoid 90º

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

73 2 9267 2

To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

Firmly grasp the body of the dryer (not the console panel).

Gently lay the dryer on the cardboard. See illustration.

64 ft (20 m)

36 ft (11 m)

58 ft (17.7 m)

28 ft (8.5 m)

54 ft (16.5 m)

31 ft (9.4 m)

48 ft (14.6 m)

23 ft (7 m)

44 ft (13.4 m)

27 ft (8.2 m)

38 ft (11.6 m)

19 ft (5.8 m)

35 ft (10.7 m)

25 ft (7.6 m)

29 ft (8.8 m)

17 ft (5.2 m)

27 ft (8.2 m)

23 ft (7 m)

21 ft (6.4 m)

15 ft (4.6 m)

1234546

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 74 75

Comments to this Manuals

No comments

Whirlpool 9700S User Manual Page 22

Comments to this Manuals

Related products and manuals for Electric laundry dryers Whirlpool 9700S