Whirlpool Commercial Dryer Service Manual download pdf

INSTALLATION

INSTRUCTIONS

COMMERCIAL DRYER

Before you begin, read the following instructions

completely and carefully. They will simplify the

installation.

After completing the installations, save these

instructions for future use.

GENERAL

Fire Hazard

- Do Not use or store gasoline, paint, thinners and

other flammable materials near dryer.

Never install dryer up against draperies or

curtains or on carpet.

Keep any and all items from falling or collecting

behind the dryer.

Replace all access panels before operating dryer.

Failure to follow these instructions could result

in a fire or explosion.

If you smell gas:

1. Open windows.

2. Don’t touch electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier.

Do Not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance. The fumes can create a fire

hazard or explosion.

It is recommended that the operator post, in a

prominent location, instructions for the customer’s use

in the event the customer smells gas. This information

should be obtained from your local gas supplier.

Post this caution in a prominent location.

NON-COIN MODELS

On non-coin operated models, the console houses the

accumulator timer with actuating arm and button.

COIN-OPERATED MODELS

On models equipped with a coin operated console, the

console houses the accumulator timer. Coin slide

mechanism, access door lock, key and coin vault and

key can be supplied by the same source that furnished

this dryer.

The accumulator timer is set to accumulate 45 minutes

(4 pins) drying time for each coin deposited. Two

additional timing cams for 30 minute (6 pins) and 60

minute (3 pins) time increments are included in the

miscellaneous parts bag.

INSTALLING AND REPLACING NYLON TIMING

CAMS ON ACCUMULATOR MECHANISMS.

INSTALL BEFORE COMPLETING ELECTRICAL

CONNECTION.

Removal of nylon timing cam.

Rotate cam by hand until “V” notch lines up

underneath the ratchet tooth. (See Figure 1.)

TIMING CAM

LINE UP NOTCH

TO CLEAR RATCHET

HUE DOWN

FIGURE 1

Insert narrow screwdriver under nylon cam, close

to the clock shaft. Lift gently off shaft. Make sure that

pressure is directly upward and the “V” notch clears

the ratchet tooth.

2. Replacement of new timing cam.

Place cam (hub down) over clock shaft, lining up

flat on shaft with flat of cam hole. (Be sure drive lug

is in place.)

Rotate cam until “V” notch lines up with ratchet

tooth.

c. Press down to seat cam on motor shaft. Make

sure that “V” notch freely clears ratchet tooth.

INSTALLING OR CHANGING SLIDE MECHANISM.

Remove the service access door of the meter case.

Lift the service access door up at the back to

remove. On new dryers install the service access

door lock.

2. Carefully remove and insert the coin slide

mechanism through the opening in the front of the

meter case console.

3. Secure the coin slide mechanism with the s6” bolt

from inside the meter case (See Figure 2).

INSTALLING OR CHANGING COIN VAULT

Put the coin vault with lock and key in the meter case

opening.

2. If you wish to install a large capacity coin vault, use a

knife to carefully remove the paint along the seam at

the bottom of the conversion bar.

3. Use a blade screwdriver and a hammer to lightly tap

along the seam area. Raise the conversion bar up to

the notches in the sides of the vault opening.

4. Remove the conversion bar and drawer guide. Install

new guide( found in parts bag) and the larger coin vault

(see Figure 3).

FIGURE 2

FIGURE 3

CONVERSION BAi

n n9

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - COMMERCIAL DRYER

INSTALLATION INSTRUCTIONS COMMERCIAL DRYER Before you begin, read the following instructions completely and carefully. They will simplify

Page 2 - GAS DRYER MODELS

This appliance is suitable for mobile home installations. The installation of the dryer must conform to the Manufactured Home Constru

Page 3

GAS DRYER MODELS RECOMMENDED GROUNDING METHOD DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUND PRONG. For your personal

Page 4 - ELECTRIC DRYER MODELS

ELECTRIC DRYER MODELS ELECTRICAL REQUIREMENTS OBSERVE ALL GOVERNING CODES AND ORDINANCES Electrical Shock Hazard l Electrical ground is re

Page 5

ELECTRIC DRYER MODELS (1 *I (2.1 (3.) Remove the terminal block cover. Connect the neutral wire of the power supply cord to the center

Page 6

ELECTRIC DRYER MODELS COPPER POWER SUPPLY CORD WITH PLAIN ENDS I30 AMPERES) (WHITE OR CENTER) PLAIN-END FIELD WIRING FIGURE 15 NOTE: The ter

Page 7

EXHAUST SYSTEM REQUIREMENTS Fire/Health Hazard B Do Not use non-metal, flexible duct. m Do Not use metal duct smaller than four inches in dia

Page 8 - MOVING OPERATION PROCEDURE

IMPORTANT OPERATING INFORMATION All models as received may have some accumulated time remaining on the timer due to factory testing.

Whirlpool Commercial Dryer Service Manual

Browse online or download Service Manual for Electric laundry dryers Whirlpool Commercial Dryer. Whirlpool Commercial Dryer Service manual User Manual

Summary of Contents

More documents for Electric laundry dryers Whirlpool Commercial Dryer

Comments to this Manuals

Whirlpool Commercial Dryer Service Manual

Browse online or download Service Manual for Electric laundry dryers Whirlpool Commercial Dryer. Whirlpool Commercial Dryer Service manual User Manual

Summary of Contents

More documents for Electric laundry dryers Whirlpool Commercial Dryer

Comments to this Manuals

Related products and manuals for Electric laundry dryers Whirlpool Commercial Dryer