Whirlpool WGFD293 Instruction Manual download pdf (Page 22)

Upright Standard Connections—Left Side Upflow

(Counterflow Similar)

Upright Drain Trap Mounting—Left or Right Side

Panel

1. Insert the drain tubes into the drain trap and position the

drain trap against the side panel.

NOTE: Drain tubes must reach the bottom of the drain trap.

2. Secure the drain trap to the side panel at the mounting holes

(dimples or crosshairs on counterflow models) located below

the grommet drain holes.

3. Attach the PVC drain line to the drain trap outlet with either a

90° elbow or coupling.

Horizontal Installations—Right Side Down

Horizontal installations with the right side down require that the

drain hoses be connected to the right side front cover drain port

and the rubber elbow drain port.

NOTE: On counterflow models, relocation of the front cover

pressure switch hose is required.

Make connections as follows:

1. Remove the rubber plug from the right side of the front cover

drain port.

NOTE: On counterflow furnaces, relocate the front cover

pressure switch hose connection from the left side pressure

tap to the right (down) side tap to guard against blocked drain

conditions. Cut the hose to appropriate length to minimize

sagging. Plug the left (unused) pressure tap with the plug

removed from right side.

2. Secure Hose A to the front cover drain tap with a red hose

clamp.

3. Route Hose A to the rear right (down) side panel grommet

holes.

4. Cut ¹⁄₄" (6.4 cm) from the end of the drain port on the

externally mounted rubber elbow. Discard cut portion.

5. Insert Tube 1 into the rubber elbow drain port and secure with

a silver hose clamp.

NOTE: Angle tube outward toward front of furnace.

6. Cut 17³⁄₄" (45.1 cm) from the long end of Hose B. Discard cut

portion.

7. Secure the remaining end of Hose B to exposed end of Tube

1 with a green hose clamp.

8. Route Hose B to the front right (down) side panel grommet

holes.

9. Cut 5¹⁄₂" (14 cm) straight length from the long end of each

Tube 2. Discard the radius pieces.

10. Insert approximately 1" (2.5 cm) of each Tube 2 through the

right (down) side panel grommet holes.

11. Secure the tubes to Hose A and Hose B using the green hose

clamps.

NOTE: Ensure that the hoses and tubes maintain a

downward slope for proper drainage and are not kinked or

bound.

For details concerning the mounting of the drain trap, refer to

“Horizontal Drain Trap Mounting” in “Condensate Drain Lines and

Drain Trap.”

Horizontal Upflow Connections—Right Side Down

(Counterflow Similar)

A. Left side panel

B. Rubber elbow

C. Rubber elbow

drain port

D. Silver hose clamp

E. Tube 1

F. Green hose clamps (3)

G. Hose B

H. Drain trap

I. Tubes 2

J. Side panel drain holes

K. Hose A

L. Front cover drain port

Cabinet Width

Models

(kBtu/Tons)

X Length to Cut from

Long End of Hose B

17¹⁄₂" (44.5 cm) 45_30 7" (17.8 cm)

21" (53.4 cm) 70_40 3¹⁄₂" (8.89 cm)

24¹⁄₂" (62.3 cm) 090_50 None

115_50

A. Front cover drain port

B. Front cover pressure tap

C. Right side panel

D. Rubber elbow

E. Rubber elbow drain port

F. Si lv e r h o s e cl a m p

G. Tube 1

H. Green hose clamps (3)

I. Drain trap

J. Tubes 2

K. Hose B

L. Hose A

M. Red hose clamp

EFGH

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 51 52

Comments to this Manuals

No comments

Whirlpool WGFD293 Instruction Manual Page 22

Comments to this Manuals

Related products and manuals for Fireplaces Whirlpool WGFD293