Whirlpool Thin Twin User Manual

I AiVhirlDoolCONSUMER SERVICES TECHNICAL EDUCATION GROUP PRESENTSLarge-Capacity Thin Twin Laundry SystemPart No.4314124 Rev. Aikers. Dishwashers, Buil

13. Move the washer to its permanent location.14. Tilt the washer forward off the floor and set back down to adjust the rear self-leveling legs.15. Ch

Preparing the Laundry System for Exhausting Left or Right1. Remove left or right side panel knockout by drilling four (4) holes at the drill location

4. Preform the flex pipe to the left or right. Pull the flexpipe through the knockout opening until the clip “snaps” into place. (Fig. 9)NOTE:

-NOTES -

SECTION TWOCOMPONENT ACCESSA WARNINGiIkElectrical Shock Hazard«¡iwDisconnect electric power from appliance before servicing. Replace all panels before

Washer Mechanism Removal1. Remove the two (2) Vi washer retaining bolts. (Fig. 14)Fig. 14Retaining Bolts2. Remove the Motor Wiring and Wiring Harness

5. Lift and pull the washer assembly forward out of the cabinet. From this position it is possible to service all the washer components, which are si

Dryer Toe Panel Access1. Remove the Transition Panel by removing the three (3) retainingscrews.2. Using a putty knife, release the two (2) retaining c

5. Remove the top two (2) retaining screws.6. Remove the bottom two (2) screws.7. Remove the Lint Screen.8. Remove the three (3) Dryer Lint Duct a

6* Remove the Blower Housing.7. Remove the Drive Belt.8. Remove the Motor Wiring. (Fig. 26)9. Remove the wiring to the broken belt switch.10. Remov

Whirlpool Regional Headquarters (760) 662-S078 Http://vuww.servicematters.com Click on Educational Solutions for more information

Dryer Belt Replacement1. Remove the Dryer Toe Panel.2. Remove the Lint Filter and the Lint Duct Assembly.3. Remove the Blower Assembly.4. Remove t

-NOTES -14

SECTION THREETROUBLESHOOTING and DIAGNOSISDRYER TROUBLESHOOTING GUIDECONDITIONPOSSIBLE CAUSEDryer will not run.No power to unit.Door switch not making

TROUBLESHOOTING and DIAGNOSISWASHER TROUBLESHOOTING GUIDEPROBLEMPOSSIBLE CAUSEIIIIIIIIIIIIIIIQgl^^1 MOTOR WILL NOTNo/low voltage to machineCheck suppl

PROBLEMPOSSIBLE CAUSE7. KNOCK DURINGAgitator splines wornReplace agitatorAGITATE.Excessive clearance on pinion thrust or main drive gearReplace gearca

13. CLOTHING DAMAGEExcessive use of bleachInstruct customerOverloading of machineInstruct customerForeign objectsRemoveWater level too lowIncrease wat

To test the centrifugal switch, remove the pump and disconnect the motor harness block from the centrifugal switch.Remove the switch fr

Check the high-speed windings by testing between the blue and white wires. A resistance reading between 3/4 ohm and 2 ohms should be pre

To test the water level switch, remove the wires from the water level switch.With the tub empty, there should be continuity from violet to

DRYER TIMERTo test the timer contacts, select the contacts to be tested; in this case, TM-OR.Using the cycle sequence chart as a reference, tu

INTRODUCTIONThis Job Aid, “LARGE-CAPACITY THIN TWIN LAUNDRY SYSTEM,“ (Part No. 4314124 Rev. A) pro-vides specific information for the installatio

DRYER MOTOR and BROKEN BELT SWITCHTo check out the motor, first remove the motor harness from the centrifugal switch. Then, set the me

HI-LIMIT THERMOSTATThe hi-limit thermostat is located on the side of the heater element (gas burner) housing.To test the hi-limit thermostat at

THERMAL CUT-OFF (Electric Models Only)The thermal cut-off is located on the side of the heater element housing.To test the thermal cut-off, set

GAS BURNERRemove the harness plug from the gas valve terminals and measure the resistance across the terminals indicated in the follow

WASHERCAMsw.±1=±=i4.5-------------77776677.56lA5.1:ZiZi-SL-iZiZiZ__|-fi.Z-Zj-fi-ZiZifiZil-lZii£.125-fiZif-ZiiZiJi 810 13ìe12T8o:§so-J0>R_K1L11-f41r

Wiring Diagram - Eiectric Dryer Modeis28

Wiring Diagram - Gas Dryer Models29

MODEL/SERIAL NUMBER PLATE LOCATIONModel/SerialThe model/serial number plate for the Whirlpool Thin Twin Laundry System is located in the dryer

“ NOTES -31

-- NOTES -32

TABLE OF CONTENTSINTRODUCTION... IITABLE OF CONTENTS

WhiflCORPORATIONMaking your world a little easier.ikers, Dishwashers, Built-In Ovens and Surlace Units, Ranges, Microwave Ovens, Trash Compactors, Roo

SAFETYA WARNING>4ELECTRIC SHOCK HAZARDDisconnect the electrical power before servicing any components .VFailure to do so can result in death or ele

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYER UNITSA. A three-wire (Fig. 2) or four-wire (Fig. 3), single phase, 120/240 volt, 60 Hz, AC only elec

A WARNINGFire HazardDo Not use nonmetal, flexible duct. Do Not use metal duct smaller that four inches in diameter. Do Not use exha

SECTION ONEINSTALLATION CONSIDERATIONSA WARNINGINJURY HAZARDMore than one person is required to lift, tilt or move the washer/dryer because of its wei

4. Wet the inside of the drain hose with water. DO NOT USE ANY OTHER LUBRICANT.5. Squeeze the ears of the drain hose clamp with a pair of pliers and