Whirlpool HOO E00 S Instruction for Use download pdf

5019 618 33044/B

EXTRACTOR OR FILTERING HOOD INSTALLATION

The minimum distance between the support surface of the recipients on the cooking device and the lowest part of the hood

must not be less than 50 cm in case of electric cookers and 65 cm for gas or combination cookers. If the installation instructions

for the gas cooker specify a greater distance, this must be taken into account. The fume hose and hose clamps are not supplied.

Contact a qualified technician for installation.

1. Mark a centre-line on the wall from the cooktop to the ceiling (1)

2. Taking into account the above-mentioned distances from the cooktop, mark the distance from the cooktop with a pencil and place the

template against the wall on the mark (2)

3. Using the template supplied, mark the holes, drill and insert the plugs (3) in the wall, partially screw in 2 screws in the top holes (4) and

hook the hood.

4. remove the grease filter/s (5)

5. Mark the bottom holes for secure fixing (6)

6. Remove the hood from the bracket, drill and insert the wall plugs (7)

7. Hook the hood, tighten the bottom screws (8) and the top screws (9).

8. Fix the flue support to the wall as close as possible to the ceiling: drill the holes and insert the 2 plugs (10), position the support (11) and fix

it with the 2 screws (12).

Extractor Version: Steam and fumes are exhausted to the outside. Proceed as follows:

fit the collar with non-return valve supplied with the product (X) onto the exhaust opening of the hood, exerting light pressure. Screws are not

required to attach the collar. Then fit the adaptor for the exhaust pipe (Y) onto the collar, exerting light pressure. Fit an exhaust pipe which is

long enough to vent externally (13A). Care must be taken to ensure that the tube and adaptor fastening does not impede the electric shutter

from opening and closing. Important: If the hood is equipped with a carbon filter, this must be removed. The discharge air must not be ducted

to a flue used for removing fumes produced by appliances using gas or other fuels, but must have a separate outlet. All national regulations on

air discharge must be observed.

Filtering Version: The air is filtered by a carbon filter and recycled in the surrounding environment. In this case, fit the special deflector (13F)

to the lower flue, fixing it with 4 screws. Important: if the hood does not have a carbon filter, order one and fit it before use.

Connect the hood to the mains supply (14) and fix the telescopic flue to the flue bracket with two screws (15A). Slide the bottom section

down into its seat on the top of the hood and fix with two screws (15B).

Preparing the flange: remove the protective film (A) from the flange and apply it to the lower edge of the frame as shown in B.

Fitting the flange: fit the three brackets (16), partially undo the 6 screws (2 per bracket), bend and position the flange between the hood and

the brackets (17) so that the side with the protective strip is facing the edge of the hood. Fix the flange as close as possible to the brackets on

the edge of the hood.

The hood’s top surface can support a maximum

weight of 10 Kg.

CZ SK H

RUS

1 2 3 4

Summary of Contents

Page 1

5019 618 33044/BEXTRACTOR OR FILTERING HOOD INSTALLATIONThe minimum distance between the support surface of the recipients on the cooking device and t

Page 2 - CONTROL PANEL

5019 618 33044/B1. Control panel2. Grease filters3. Grease filter handles4. Light above cooker (according to the model)5. Telescopic flueTo clean the

Page 3 - IMPORTANT INSTRUCTIONS FOR

5019 618 33044/BSAFEGUARDING THE ENVIRONMENT1. PackingPacking materials are 100% recyclable and are marked with the recycling symbol .Comply with the

Page 4

5019 618 33044/BElectrical connectionThe mains voltage must match that given on the rating plate located inside the hood. If provided with a plug, co