Whirlpool WRF953CIHB Use and Care Manual download pdf (Page 20)

When adjusting temperature set points,

use the following chart as a guide:

CONDITION: TEMPERATURE ADJUSTMENT:

Refrigerator too cold Refrigerator setting 1° higher

Refrigerator too warm Refrigerator setting 1° lower

Freezer too cold Freezer setting 1° higher

Freezer too warm/

Too little ice

Freezer setting 1° lower

Max Cool

The Max Cool feature assists with periods of high refrigerator

use, full grocery loads, or temporarily warm room temperatures.

■ To turn on the Max Cool feature, press MAX COOL. When the

button is pressed, the icon will blink three times and appear

on the display screen.

■ To manually turn off the Max Cool feature, press MAX COOL

and the display will blink three times and turn off.

The Max Cool feature will remain on for 24 hours unless

manually turned off. Adjusting the refrigerator temperature

will automatically turn off the Max Cool feature.

Max Ice

The Max Ice feature assists with increasing the cooling for the

freezer compartment in order to increase ice production.

■ To turn on or off the Max Ice feature, press MAX ICE. When

the button is pressed to turn the feature on, the icon will blink

three times and appear on the display screen.

■ To manually turn off the Max Ice feature, press MAX ICE and

the display will blink three times and turn off. The Max Ice

feature will remain on for 24 hours unless manually turned off.

Adjusting the refrigerator temperature will automatically turn

off the Max Ice feature.

NOTE: Setting the freezer to a colder temperature may make

some foods, such as ice cream, harder.

Water Filter Replacement

The displays indicate the status of the water filter. To reset the

filter, press and hold MAX ICE and MAX COOL for 3 seconds.

After countdown, the “Good” icon will blink three times and

remain lit.

NOTE: The Water Filter status lights on the internal controls will

let you know when to change your water lter.

■ Order Filter (yellow): Order a replacement water lter.

■ Replace Filter (red): Replace the water lter. While you are

dispensing water, the “Replace” lter icon will ash constantly

from beginning to the end of dispensing. After 14 days

without replacing the water lter, the “Replace” lter icon will

blink seven times and an alert tone will sound three times,

at the end of dispensing. See the “Water Filtration System”

section.

NOTE: The "Replace" lter icon will remain illuminated if a

lter reset is not done.

■ Reset Filter: Press and hold MAX ICE and MAX COOL at

the same time on the Temperature Control display for 3

seconds to reset water lter. The display will do a 3-second

countdown and then ash the icon and play a tone.

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are

preset at the factory.

When you rst install your refrigerator, make sure that the

controls are still set to the recommended set points. The factory-

recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.

IMPORTANT:

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder-than-

recommended setting will not cool the compartments any

faster.

■ If the temperature is too warm or too cold in the refrigerator

or freezer, rst check the air vents to be sure they are not

blocked before adjusting the controls.

■ The recommended settings should be correct for normal

household use. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is rm.

NOTE: Areas such as a garage, basement, or porch may have

higher humidity or extreme temperatures. You may need to

adjust the temperature away from the recommended settings

to accommodate for these conditions.

■ Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

View Temperature Set Points

Touch ▼/▲ for refrigerator or ▼/▲ for freezer to toggle through

temperature set points.

NOTE: To view temperature in degrees Celsius, touch

and hold the °F-°C button for 3 seconds and the temperature

display will change. To return to Fahrenheit, touch and hold

°F-°C for 3 seconds and the temperature display will change.

To activate Temperature mode for Pantry Drawer, touch

DRAWER and toggle through four optional temperature settings:

Meats, Deli-Cheese, Assorted, and Drinks. The display will show

the temperature set point of the selected setting for the pantry

drawer.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (1°C to 7°C)

Freezer set point range: -6°F to 5°F (-22°C to -15°C)

1. Touch ▼/▲ to adjust the Refrigerator zone. The display will

show the temperature set point of the selected compartment

as shown.

2. When the temperature is in the range of Freeze Shield, the

display will light up. Freeze Shield is active at the coldest

freezer set point.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 80 81

Comments to this Manuals

No comments

Whirlpool WRF953CIHB Use and Care Manual Page 20

Comments to this Manuals

Related products and manuals for Fridges Whirlpool WRF953CIHB