Whirlpool AGS 419/WP Installation Manual download pdf (Page 8)

GENERAL INSTRUCTIONS

1. Please read this booklet carefully as it contains important information

concerning safe installation, use and maintenance.

Please keep this booklet in a safe place for further consultation by other

operators.

2. The appliance must be installed by a trained technician in accordance

with the manufacturer’s instructions.

3. The appliance must only be used by trained personnel.

4. Turn the appliance off in the event of a failure or malfunction. Should

repairs be necessary, contact only an authorised service centre and

insist on manufacturer’s spare parts.

Failure to observe the above can compromise the safety of the

appliance.

5. The manufacturer will not accept responsibility for any work carried

out on appliances where instructions indicated in the manual are not

heeded.

The current manual may not be reproduced in any way.

Radio Interference: This appliance conforms to the Ministerial

Directive dated 13.04.1989 and EEC Directive 87-308 pertaining to the

suppression of radio interference.

INSTRUCTIONS FOR THE INSTALLER

REMOVING PACKAGING

Removal of packaging and transport

Remove the protective film taking care not to scratch the surface (use

scissors or a blade if necessary). Next, remove any polystyrene

protection.

Where the appliance has stainless steel components, remove the

protective film very slowly, without tearing, to avoid leaving traces of

adhesive.

Appliances must be moved using a fork lift trolley. Insert the forks under

the pallet and move the appliance to the site of installation taking care

that the load is properly balanced.

Caution: To avoid tipping the appliance over, do not push or pull it during

transport.

Disposing of packaging

Packaging material must be disposed of in conformity with current local

safety regulations.

Plastic packaging materials that can be recycled are labelled as

follows:

polyethylene: outer protective film, bag

PE instructions

polypropylene: straps

expanded polystyrene: corner protectors

compressed cardboard: corner protectors

Caution: PUT ON PROTECTIVE GLOVES BEFORE

BEGINNING INSTALLATION.

POSITIONING AND ASSEMBLY OF ELEMENTS

If the unit is installed in a place where there are corrosive substan-

ces (chlorine, etc.) it is advisable to go over all the stainless-steel

surfaces with a cloth moistened with paraffin oil in order to form a

protective film.

The appliance is intended for specific industrial use; any other use

is to be considered improper.

The hood must be positioned according to the following

parameters: it must be connected to an efficient flue directly to the

outside, of adequate size for the hood’s extraction capacity.

the recommended height from the floor is 1900/2000 mm;

the perimeter of the hood must protrude by at least 20 cm with

respect to the area of the appliances, and in any case that value

must comply with current local regulations.

To ensure efficient operation, install the appliance in an adequately

ventilated place.

Important! Make sure the ceiling or wall can take the weight

of the hood; otherwise have the necessary masonry

reinforcement work carried out.

HOOD INSTALLATION

The hood can be installed using the plugs and eyebolts supplied.

If the floor is made from hollow brick, resin plugs (not supplied) can

be used.

For installation operations, proceed as follows

- Mark the places for fitting the plugs on the ceiling or wall and drill

with a Ø 14 mm bit.

- Fit the M8 plugs.

- Prepare the length of the threaded bars, or chains, and hang the

hood from the ceiling, operating as described below.

Installation with chains Fig.1 page 2

- Screw the Ø 8 MA eyebolts to the plugs in the ceiling;

- fit another set of eyebolts directly on the hood using the holes

already prepared on the top edge

- connect the various pairs of eyebolts by means of the chains and

“S” hooks

Installation with threaded bars Fig.2 page 3

- Screw the threaded bars directly on the plugs fitted in the ceiling.

- Secure with washers and nuts, then fit the bar cover tubes.

- Lift the hood and position it so that the bars enter the holes

already prepared in the top edge, then secure with nuts and

washers.

HOOD CONNECTIONS

The following connections are provided for the various types of

hoods:

- Fume exhaust (for all hoods)

- Compensation air inlet (only for hoods with compensation)

- Electrical connections (only for Ventil hoods and hoods with

compensation)

Water connections (only for self-cleaning hoods)

Compensation air inlet connection

The air inlet ducts for compensation hoods must be suitable sized.

The air inlet ducts must always be insulated inside.

CONNECTION OF VENTIL HOODS TO THE SPEED VARIATOR

Connection to the power supply must be carried out in

accordance with current regulations.

Before connecting, make sure the voltage and frequency match

that given on the dataplate.

An omnipolar switch of suitable capacity with contact opening

distance of at least 3 mm must be installed ahead of the appliance.

The switch must be installed in the permanent electrical system of

the building, in the immediate vicinity of the appliance; line fuses of

10 A capacity must also be installed.

The speed variator is supplied as an accessory. It can be used

in hoods with built-in fan, and must positioned in an easily

accessed place, protected against impacts and away from

heat sources.

The connection cable must be of the flameproof type with min.

section of 2.5 mm².

For connection, comply with the diagram given inside the regulator.

Lamp connection

• The lamps fitted in Supertredil range hoods are already wired

together; just connect the feed wires (220V single phase) to the

terminals located inside the connector blocks fitted on the roof of

the hoods.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Whirlpool AGS 419/WP Installation Manual Page 8

Comments to this Manuals

Related products and manuals for Household fans Whirlpool AGS 419/WP