Whirlpool DU920QWDB4 User Manual download pdf (Page 6)

To change door

panel color

NOTE: The opposite side of the door

color panel is a different color.

To change access

color panel

(For models so equipped)

This panel is

narrower

than access

panel.

File or sand

edges of wood

panel to avoid

slivers.

oar

-3d

Ior

lot

Personal Injury Hazard

Wear gloves and handle panels

carefully.

Cut metal edges may cause personal

injury or damage to other materials.

Personal Injury Hazard

Wear gloves and handle panels

carefully.

Cut metal edges may cause personal

injury or damage to other materials.

4l+

7132”

bottom

edge

Push UD

Figure

Insert finger

Cut door pa

clear acces

with thumbs on

each end of

access panel

top trim to

unsnap trim.

under one end-of

retainer and pull

towards you in a

peeling action. Set

retainer aside.

Lift

door

panels at

outer edges.

Use one hand

to bow bottom

of panel.

Remove

panel(s). Do Not

remove spacer.

when door is in

open position.

I I

Heavy-duty door springs must be used if

custom door panel weighs more than 4

pounds. Heavy-duty Door Springs Kit,

Part No. 4318050, is available from your

local dealer or parts supplier. Maximum

door weight is 8 pounds.

Remove top trim and set it aside.

w Carefully

slide color

access panel

upwards and

remove. Do Not

Wood access panel

This panel is wider than door panel.

23-s/16” -4

remove spacer.

With

desired color

facing out, bow

access panel

and insert into

access panel

4-7116”

3. LE2ne pJ 1

door panel(s),

All edges routed to 7/32” thickness.

frame. Slide panel down into groove

along bottom of access panel frame.

Top view

,7/32” thick

with desired color

facing out, into

one side of door

frame.

I Line up

edges of top trim

with sides of

access panel

frame. Tilt back of

Figure 6

Bow door

panel(s)

Cut wood door and access panels

using specified dimensions. Make sure

wood grain direction matches cabinet

wood grain.

File or sand edges of wood panels

to avoid slivers.

Dishwasher is subject to some humidity.

Cover both sides and edges of wood

panels with moisture-resistant sealer.

trim down and slide into place. Snap

front of trim down to cover top edge of

access panel.

and insert other

side of door

panel(s) into

door frame.

To install

customized wood

panels in door and

access panel

Dishwasher door panel and access

panel (if model is so equipped) can be

customized to match wood cabinets. A

standard l/4” (7/32” actual thickness)

wood panel can be used as is for

customizing the door and access

panels.

A door panel thicker than 7/32”,

requires routing the top and bottom to a

7/32” thickness,

An access panel thicker than 7/32”,

requires routing all four edges to a 7/32”.

It is recommended that a cabinet-

maker cut the customized panels

because of the precise cuts required.

(See Figures 5 and 6.)

Wood door panel

Cut accurately for a snug fit between

door side frames. Note: Custom panel

fits between, Not inside frame.

control console

Push in

on door

panel(s) near the top

and slide panel(s) and

spacer up inside

bottom of control

console, allowing

panel(s) to rest on

channel at bottom

of door.

Personal Injury Hazard

Wear gloves and handle panels

carefully.

Cut metal edges may cause personal

injury or damage to other materials.

Insert finger

under one end of

retainer and pull

towards you in a

peeling action. Set

retainer aside.

Lift door

panel(s) at outer

edges. Use one hand to

bow bottom of panel(s).

Remove panel(s) and

spacer. Save panel(s)

and spacer for future use.

top of panel

under control

console

ins

sid

panel fits between,

not inside, door frame

Insert top of wood door panel

between sides’of door frame about 3”

below console. Rotate wood door panel

down against dishwasher door. Slide top

edge of wood door panel under bottom

edge of console. Press lower portion of

wood door panel in place between sides

of door frame, allowing wood door panel

to rest on channel at bottom of door.

\Iv/ .

Snap one end of retainer into

channel as shown. Push inward

while sliding thumb along full length of

retainer.

Panel E

1 2 3 4 5 6 7

Comments to this Manuals

No comments

Whirlpool DU920QWDB4 User Manual Page 6

Comments to this Manuals

Related products and manuals for Dishwashers Whirlpool DU920QWDB4