Whirlpool W10115228B User Manual Page 13
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
13
A
B
C
D
Plan pipe tting connection
2.
A combination of pipe ttings must be used to connect dryer
to existing gas line. A recommended connection is shown.
Your connection may be different, according to supply line
type, size, and location.
A. 3/8" exible gas connector
B. 3/8" dryer pipe
C. 3/8" to 3/8" pipe elbow
D. 3/8" pipe-to-are adapter tting
Open shut-off valve in supply line; valve is open when handle
is parallel to gas pipe. Then, test all connections by brushing
on an approved noncorrosive leak-detection solution.
Bubbles will show a leak. Correct any leaks found.
†®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.
Connect Vent
Connect vent to exhaust outlet
1.
Move dryer to nal location
2.
Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure vent is
clean. Dryer vent must t over dryer exhaust outlet and inside
exhaust hood. Check that vent is secured to exhaust hood
with a 4" (102 mm) clamp.
Move dryer to nal location. Avoid crushing or kinking vent.
After dryer is in place, remove corner posts and cardboard
from under the dryer.
Connect vent to exhaust hood
2.
Vent must t over the exhaust hood. Secure vent to exhaust
hood with 4" (102 mm) clamp. Run vent to dryer location
using straightest path possible. Avoid 90° turns. Use clamps
to seal all joints. Do not use duct tape, screws, or other
fastening devices that extend into interior of vent to secure
vent, because they can catch lint.
A
B
Connect gas supply to dryer
1.
Remove red cap from gas pipe. Using a wrench to tighten,
connect gas supply to dryer. Use pipe-joint compound
on threads of all non-ared male ttings. If exible metal
tubing is used, be sure there are no kinks.
NOTE: For LP gas connections, you must use pipe-joint
compound resistant to action of LP gas. Do not use
TEFLON
®†
tape.
Make Gas Connection
Open shut-off valve
3.
A
B
Closed valve
Open valve
Non-ared
male tting
Flared
male tting
- Table of Contents 1
- Table des matières 1
- DRYER SAFETY 2
- INSTALLATION REQUIREMENTS 4
- Location Requirements 5
- ELECTRIC DRYER POWER 7
- HOOKUP – CANADA ONLY 7
- GAS DRYER POWER 8
- GROUNDING INSTRUCTIONS 9
- SAVE THESE INSTRUCTIONS 9
- Venting Requirements 10
- Plan Vent System 11
- Venting Kits 11
- Vent System Chart 12
- Install exhaust hood 12
- Level dryer 14
- Remove screws from door 19
- Flip door over 19
- Attach door hinges 19
- Remove and transfer plugs 19
- Rotate outer door 19
- SÉCURITÉ DE LA SÉCHEUSE 23
- EXIGENCES D’INSTALLATION 25
- Exigences d’emplacement 26
- 13¾" 27
- (349 mm) 27
- CONSERVEZ CES INSTRUCTIONS 28
- RACCORDEMENT D’UNE 29
- SÉCHEUSE À GAZ 29
- Canalisation de gaz 30
- L’ÉVACUATION 32
- Trousses d’evacuation 33
- Ôter les vis des charnières 40
- Retourner la porte 40
- Fixer les charnières de porte 43
- Séparer la porte interne 46
- Retirer la gâche de porte 46
- W10115228B 48
- W10115229B-SP 48
Related products and manuals for Electric laundry dryers Whirlpool W10115228B
(56 pages)
(16 pages)
(48 pages)Philips QC5126/15 manuály
Uživatelské manuály a uživatelské příručky pro Zastřihovače vlasů Philips QC5126/15.
Poskytujeme 1 manuály pdf Philips QC5126/15 ke stažení zdarma podle typů dokumentů: Datový list
Comments to this Manuals