1W10775223BW10775224B - SPTable of Contents DRYER SAFETY ... 2INSTALLATION REQUI
104-Wire Direct Wire ConnectionIMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections.Dire
111. Prepare your 3-wire cable for direct connection 1"(25 mm) 3½"(89 mm)2. Remove center screwB5. Connect remaining wires4. Connect
12Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center terminal block screw (B). Tig
13Exhaust hoods:Elbows: 45° elbows provide better airflow than 90° elbows.Clamps: Use clamps to seal all joints. Exhaust vent must not be connect
14The “Vent System Charts” provide venting requirements that will help achieve best drying performance.Special provisions for mobile homes:Exhaust ve
15Install Vent System1. Install exhaust hood12" min.(305 mm)12" min.(305 mm)2. Connect vent to exhaust hoodInstall exhaust hood and use caul
165. Attach long hose to dryer fill valve and tighten couplingRemove protective cap from water inlet valve. Attach other end of long hose to fill val
172. Adjust leveling legsIf dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once
18IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding.Using a T25® screwdriv
194. Remove outer window assembly from trim ringUsing a Phillips screwdriver, remove the 2 screws from the outer window retainer and rotate the outer
2DRYER SAFETY
20With the edge with 2 notches at the top, align the notches on the outer window assembly with the tabs on the trim ring and lower into place as shown
219. Reinstall inner door assemblyPosition the door with the inside of the door facing up. Reinstall the 10 screws securing the inner door to the out
223. Remove inner door from outer doorPosition the door with the inside of the door facing up. Using a Phillips screwdriver, remove the 10 screws sec
231. Remove door from dryerIMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceedin
244. Remove hinge and latchUsing a T25® screwdriver, remove the 3 screws securing the latch plate and latch backing plate and the 5 screws holding the
252. Move the door strikeUsing a T25® screwdriver, remove the 2 screws securing the door strike to the door frame of the dryer. Remove the 4 screws ab
266. Reattach inner door to outer door Position the inner door on the outer door assembly. Using a Phillips screwdriver, secure with the 13 screws re
W10775223BW10775224B - SP©2015. All rights reserved.Used under license in Canada.11/15
3INSTALLATION REQUIREMENTSTOOLS AND PARTSGather the required tools and parts before starting installation.Tools needed:Flat-blade screwdriver #2 Phill
4DRYER DIMENSIONSBack view:61/2"(165 mm)297/8"*(759 mm)31/2"*(89 mm)61/8"*(156 mm)143/8"(365 mm)3/4"*(18 mm)NOTE: Most i
5Installation spacing for recessed area or closet installationAll dimensions show recommended and minimum spacing allowed. Additional spacing shoul
6Then choose a 4-wire power supply cord with ring or spade terminals and UL-listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m
7For direct wire installations:ELECTRICAL INSTALLATIONFor power supply cord installations:Remove hold-down screw and terminal block cover.1. Choose el
8Power supply cord strain relief4-Wire Power Supply Cord ConnectionPower Supply Cord Connection4-wire receptacle (NEMA type 14-30R)4-prong plugSpade
93-wire receptacle (NEMA type 10-30R)3-prong plugSpade terminals with upturned endsRing terminals3. Connect remaining wires2. Connect neutral wireCB4.
Comments to this Manuals