Whirlpool WGFD293 Instruction Manual download pdf (Page 23)

Horizontal Installations—Left Side Down

Horizontal installations with the left side panel down will require

the drain hoses to be connected to the left side front cover drain

port and the side drain port on the rubber elbow.

1. Remove the rubber plug from the front cover left (down) side

drain port.

2. Relocate the front cover pressure switch hose connection

from the right side (as shipped) pressure tap to the left (down)

side tap.

NOTE: The pressure switch hose must be connected to the

down side to guard against blocked drain conditions. Cut the

hose to the appropriate length to minimize sagging. Plug the

right (unused) pressure tap with the rubber plug removed

from the left side.

3. Secure Hose A to the front cover drain port with a red hose

clamp.

4. Route Hose A to the rear left (down) side panel grommet

holes.

NOTE: For left side drainage, grommets must be relocated to

the left side panel.

5. Remove the rubber cap from the side drain port on the rubber

elbow.

6. Secure the short end of Hose B to the rubber elbow side

drain port using a green hose clamp.

NOTES:

■ For left side drainage, route Hose B to the far left (down)

side panel grommet holes.

■ Horizontal left side connections (when using a new side

port drain elbow) does not require connecting a hose to

the induced draft blower housing.

7. Cut 5¹⁄₂" (14 cm) straight length from the long end of each

Tube 2. Discard radius ends.

8. Insert approximately 1" (2.5 cm) of each Tube 2 through the

left side panel grommet hole.

9. Secure the tubes to Hose A and Hose B with the green hose

clamps.

NOTE: Tube must reach bottom of trap.

NOTE: Ensure that the hoses and tubes maintain a downward

slope for proper drainage and are not kinked or bound.

For details concerning the mounting of the drain trap, refer to

“Horizontal Drain Trap Mounting” in this section.

Horizontal Upflow Connections—Left Side Down

(Counterflow Similar)

Horizontal Drain Trap Mounting—Left or Right

Side Panel

1. Position the drain trap against the side panel with the drain

tubes inserted into the trap.

NOTE: The trap may be orientated with the outlet facing

either the furnace’s top cover or base pan.

2. Secure the drain trap to the side panel at the dimples or

crosshairs located on either side of the grommet drain holes.

3. Confirm that the tubes reach the bottom of the drain trap and

that all of the hoses maintain a downward slope and are not

kinked or binding.

4. Attach the PVC drain line to the drain trap outlet with either a

90° elbow or coupling.

ELECTRICAL CONNECTIONS

Wiring Harness

The wiring harness is an integral part of this furnace. Field

alteration to comply with electrical codes should not be required.

Wires are color coded for identification purposes. Refer to the

wiring diagram for wire routings. If any of the original wire as

supplied with the furnace must be replaced, it must be replaced

with wiring material having a temperature rating of at least 105°C.

Any replacement wiring must be a copper conductor.

A. Induced draft blower drain port

B. Hose B

C. Green hose clamps (3)

D. Side panel grommet holes

E. Tubes 2

F. Drain trap

G. Hose A

H. Red hose clamps

I. Front cover drain port

J. Left side panel

FEDCG

HIJ

To avoid the risk of electrical shock, wiring to

the unit must be polarized and grounded.

WARNING

HIGH VOLTAGE!

WARNING

To avoid personal injury or death due to

electrical shock, disconnect electrical

power before servicing or changing any

electrical wiring.

Label all wires prior to disconnection when servicing

controls.

Wiring errors can cause improper

and

dangerous

operation. Verify proper operation after servicing.

CAUTION

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 51 52

Comments to this Manuals

No comments

Whirlpool WGFD293 Instruction Manual Page 23

Comments to this Manuals

Related products and manuals for Fireplaces Whirlpool WGFD293