Whirlpool ED5NTGXMQ00 User Manual download pdf (Page 8)

4. Align and replace the top left hinge as shown (see Graphic 4).

Tighten screws.

Style 1

■

Reconnect both ground wires.

■

Reconnect wiring plug.

Style 2

■

Reconnect wiring plug.

5. Replace left hinge cover and screws.

6. Replace the refrigerator door by carefully lifting the door onto

the bottom right hinge.

7. Align and replace the top right hinge as shown (see

Graphic 6). Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug into a grounded 3 prong outlet.

Door Closing

Your refrigerator has two front adjustable rollers — one on the

right and one on the left. If your refrigerator seems unsteady or if

you want the doors to close more easily, adjust the refrigerator's

tilt using the instructions below:

1. Move the refrigerator into its final position.

2. The two leveling screws are part of the front roller assemblies,

which are at the base of the refrigerator on either side (see

Graphic 8).

3. Use a hex-head socket wrench to adjust the leveling screws.

Turn the leveling screw to the right to raise that side of the

refrigerator or turn the leveling screw to the left to lower that

side. It may take several turns of the leveling screws to adjust

the tilt of the refrigerator (see Graphic 8).

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

4. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

5. Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Water Supply Connection

Read all directions carefully before you begin.

IMPORTANT:

■

If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

■

All installations must meet local plumbing code requirements.

■

Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Tools required: Flat-blade screwdriver, ⁷⁄₁₆ in. and ¹⁄₂ in. open-end

wrenches or two adjustable wrenches, ¹⁄₄ in. nut driver and drill

bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄ in.

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Beforepurchasing,makesureasaddle-typevalvecomplieswith

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆ in.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Cold water supply

Connect the ice maker to a cold water line with water pressure

between 30 and 120 psi (207-827 kPa). If you have questions

about your water pressure, call your utility company.

Connecting to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½ in. to 1¹⁄₄ in. (1.25 cm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of

the pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

1. Do not remove screw 1.

3. Green ground wire screw

2. Ground wires

1. Do not remove screw 1.

2. Wiring plug

WARNING

Electrical Shock Hazard

Reconnect both ground wires.

Failure to do so can result in death or

electrical shock.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 55 56

Comments to this Manuals

No comments

Whirlpool ED5NTGXMQ00 User Manual Page 8

Comments to this Manuals

Related products and manuals for Fridges Whirlpool ED5NTGXMQ00