Whirlpool GR2FHTXV User Manual download pdf (Page 5)

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Water Dispenser.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill ice container.

Refrigerator Doors

TOOLS NEEDED: ⁵⁄₁₆" hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat 2"

putty knife.

IMPORTANT:

■ All graphics referenced in the following instructions are

included later in this section after “Final Steps.” The graphics

shown are for a right-hand swing refrigerator (hinges factory

installed on the right).

■ If you only want to remove and replace the doors, see

“Remove Doors and Hinges” and “Replace Doors and

Hinges.”

■ Depending on your model, you may have standard (Style 1) or

contour (Style 2) doors. If you are going to reverse the door

swing, follow the instructions for the appropriate door style.

■ Before you begin, turn the refrigerator control OFF, and

remove food and adjustable door or utility bins from doors.

Remove Doors and Hinges (all models)

1. Unplug refrigerator or disconnect power.

2. Open refrigerator door and remove base grille from the bottom

front of the refrigerator. See Base Grille graphic.

3. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

A. Refrigerator water tubing

B. Nut (provided)

C.Bulb

D.Coupling (provided)

E. Ferrule (purchased)

F. Nut (purchased)

G.Household water line

A. Bulb

B. Nut (provided)

A B C D E F G

⁵⁄₁₆

" Hex-Head Hinge Screw

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

1 2 3 4 5 6 7 8 9 10 ... 48 49

Comments to this Manuals

No comments

Whirlpool GR2FHTXV User Manual Page 5

Comments to this Manuals

Related products and manuals for Fridges Whirlpool GR2FHTXV