Whirlpool ADN 103 Instruction for Use

ICE FLAKERSRange

10 Model: ICE QUEEN 150 / 200 / 400 / 550

11 MODEL REFRIGERANT CHARGE HIGH PRESURE LOW PRESURE TOTAL AMPS FUSE RATING COMPRESSOR POWER TOTAL POWER MINIMUM MAXIMUM AVERAGE (2) (1

12 Model: ICE QUEEN 1100 MODEL COOLING WATER CONSUMPTION (L/Hour) WATER CONSUMPTION (L/Hour) NET WEIGHT (KG) DIMENSIONS (CRA

13 PRODUCTION TABLES FOR ICE FLAKERS IQ135A IQ150A 45 104 102 96 92

14 Water Quality: 550 ppm. total solids Water Temperature: 15°C Ambient Temperature: 20°C Ice production and quality is heavily dependent on the follo

15 Upon receipt, thoroughly inspect the packing container. If there appears to be damage to the container contact the shipper immediately. Unpack uni

16 INSTALLATION Recommended Placement of Unit IMPORTANT! ICE QUEEN machines are intended to operate at room temperature between 5°C and 43°C and wit

17 d) PURIFIED WATER: A 10% reduction in overall production may occur. Connecting Unit To Water Source • Use 1.3 m. flexible tube (with the two fil

18 OPERATION Preliminary Checks a) Is machine levelled? b) Are voltage and frequency of mains supply the same as indicated on rating plate? c) Is dr

19 2. Make sure fan blades don't come into contact with anything and that none of the tubes vibrate. Inspection and Adjustment of Water Level i

2 TABLE OF CONTENTS Introduction Warnings...

20 ADJUSTMENTS Expansion valve. DO NOT TOUCH THE EXPANSION VALVE. Water Level The purpose of maintaining proper water levels is to allow adequate w

21 Pressure-controlled Valve on cooling water circuit • The purpose of this valve is to control cooling water flow to the condenser, so as to maintai

22 Safety pressostat

23 INSPECTION AND REPLACEMENT PROCEDURES Lower bearing Materials needed: - PHILLIPS N°2 Screwdriver - M8 Screws (*) - 5 mm Allen key - Nylon head ham

24 Procedure: 1) Remove top screw on gearbox. 2) Remove the four screws that hold flange. 3) Remover gearbox using extractor Assembly: 1) Lub

25 Upper bearing (depending on the model) Materials needed: § Extractor § PHILLIPS N°2 Screwdriver § M8 Screws (110 mm) § No.12-13 monkey wrenc

26 MAINTENANCE AND CLEANING INSTRUCTIONS IMPORTANT! **Maintenance and cleaning procedures as well as problems derived from failing to carry them out

27 MAINTENANCE AND CLEANING PROCEDURES WARNING: Unit should always be disconnected during maintenance/cleaning procedures. Water Condenser 1) Disco

28 11) Slowly add bleach to water trough for at least 5 minutes. Allow machine to make ice for at least 15 minutes. WARNING:** Discard ice produced d

29 NOTE: Newly installed electromechanical control devices will suffer variations in their adjustment caused by the machine’s own functioning. Once a

3 Troubleshooting ...32

30 SPECIAL ADVICE CONCERNING R-404 REFRIGERANT • R-404 is a mixture of 3 liquid-phase gases. On evaporating, the 3 component gases separate • Always

31 TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION 1) Machine not running. A) There is no power. A) Check power source. B) Water trough is

32 G) Refrigerant leak G) Repair leak and recharge refrigerant. H) Water level in trough is low. Water consumption is greater than buoy valve pas

33 PROBLEM PROBABLE CAUSE SOLUTION 6) Water leaks A) Water from trough overflows and falls into ice bin. Buoy valve does not close. A) Adjust

4 DESCRIPTION Main Features of the Machine § 18/8 stainless steel housing § Powerful speed reducer (24Kg./m. @ 7 rpm.) § Copper evaporator on p

5 IQ monofásica esquema eléctrico - wiring diagram

6 IQ-400-550 / R404A/ trifásica esquema eléctrico - wiring diagram

7

8

9 SPECIFICATIONS Model: ICE QUEEN 135 S60 MODEL ICE BIN STORAGE CAPACITY (KG) COOLING WATER CONSUMPTION (L/Hour) WATER CONS