Whirlpool 1188018 Specifications download pdf (Page 16)

Mode

Temperature

Press MODE until you see the indicator light come on for the •

setting you desire.

Choose Auto, Cool, Fan Only or Power Saver.

• Auto--Cools room while it automatically controls fan

speed. You cannot change fan speed, but you can adjust

temperature by pressing the plus or minus button.

• Cool--Cools room. You can adjust temperature by

pressing the plus or minus button. You can select fan

speed by pressing FAN SPEED.

• Fan Only--Only the fan runs. You can select the fan

speed by pressing FAN SPEED, but you cannot adjust the

Temperature control setting. Display shows the current

room temperature.

• Power Saver--Fan runs only when cooling is needed. Fan

stops running when the room temperature matches the

Temperature control setting. You can select the fan speed

by pressing FAN SPEED.

Because the fan does not circulate the room air •

continuously, less energy is used, but the room air is not

circulated as often. Use Power Saver when you are

asleep or away from home.

0 0 0 0

MODE Auto Cool FanOnly Power

Saver

Fan Speed

NOTE: The Fan Speed button will operate only when Cool, Fan

Only or Power Saver mode has been selected.

1. Press FAN SPEED until you see the indicator light come on

for the setting you desire.

2. Choose Turbo, High or Low.

Turbo¢_

s;°e°ed® "flI

L0w U

Filter Monitor

1. When Filter indicator light is lit or flashing, remove, clean and

replace air filter. See "Cleaning the Air Filter."

2. Press and hold FILTER for 3 seconds after cleaning and

replacing the air filter. This resets the Filter Monitor.

FILTER

Hold to Reset

NOTE: After 360 hours of fan operating time, the Filter indicator

light will turn on. It will remain on for 180 hours or until you press

FILTER. After 180 hours, it will flash. It will continue flashing until

you press FILTER.

Press the plus button to raise the temperature. Room

indicator light will turn off, and Set indicator light will turn on.

Display shows the Temperature control setting. Each time you

press or hold the plus button, the temperature will increase

1° until it reaches 86°F (30°C).

NOTE: After 3 seconds, Set indicator light will turn off, and

Room indicator light will turn on. Display will show the current

room temperature.

Press the minus button to lower the temperature. Room

indicator light will turn off, and Set indicator light will turn on.

Display shows the Temperature control setting. Each time you

press or hold the minus button, the temperature will decrease

1° until it reaches 64°F (18°C).

NOTE: After 3 seconds, Set indicator light will turn off, and

Room indicator light will turn on. Display will show the current

room temperature.

To change the temperature display from °F to °C:

1. Turn off the air conditioner.

2. While the air conditioner is off, press and hold down the

MODE and FAN SPEED buttons while pressing POWER to

turn on the air conditioner.

NOTE: Follow these same steps to change the temperature

display from °C to °E

Timer delay

To set the Timer for a 1- to 24-hour delay until the air

conditioner turns off (the air conditioner must be On):

1. Press TIMER. Timer indicator light will flash. Hour indicator

light will turn on, and display will show remaining hours

before air conditioner will turn off.

Timer

Press the plus or minus button to adjust the delay time (1 to

24 hours).

Press TIMER again or wait 10 seconds. Timer indicator light

will remain on. Hour indicator light will turn off, and Room

indicator light will turn on. Display will show the current room

temperature.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 43 44

Comments to this Manuals

No comments

Whirlpool 1188018 Specifications Page 16

Comments to this Manuals

Related products and manuals for Split-system air conditioners Whirlpool 1188018