Whirlpool WGFD295 Instruction Manual download pdf (Page 20)

Standard Right or Left Side

Drain Hose Connections

All installation positions require the use of the drain trap, hoses,

tubes and clamps. The following quantity of hoses, tubes, and

hose clamps are provided with the unit.

Hose and Tube Identification

Upright Installations—Trap on Right Side

In an upright installation, drain hoses are connected to drain

ports on the rubber elbow and the recuperator coil front cover.

The drain lines are then routed through the right side panel and

into the drain trap secured to the outside of the cabinet.

NOTE: Refer to “Alternate Vent/Flue Hose Connections” for

upright installations using an alternate vent/flue outlet,

1. Remove the rubber plug/cap from the right side of the front

cover drain port.

2. Secure Hose A to the front cover drain port with a red hose

clamp.

3. Route Hose A to the rear side panel grommet hole.

4. Cut and remove ¹⁄₄" (6.4 mm) from the end of the drain port on

the rubber elbow.

5. Insert Tube 1 into the rubber elbow drain port and secure with

the silver hose clamp. Angle Tube 1 outward toward the front

of the furnace.

6. Cut 17³⁄₄" (45.1 cm) from the long end of Hose B and discard.

7. Secure the remaining Hose B to Tube 1 with a green hose

clamp.

8. Route the other end of Hose B to the front right side panel

grommet hole.

NOTE: For details concerning the mounting of the drain trap,

refer to “Upright Drain Trap Mounting.”

9. Insert the short end of each Tube 2 through the side panel

grommet holes.

10. Secure the tubes to Hose A and Hose B with the green hose

clamps.

NOTE: Ensure hoses and tubes maintain a downward slope

for proper drainage and that they are not kinked or binding.

Upright Standard Connections—Right Side Upflow

(Counterflow Similar)

Alternate Vent/Flue Drain Hose Connections

Upright installations using the alternate vent/flue outlet will

require right side only drain hoses to be connected as follows.

Refer to “Vent/Flue Pipe and Combustion Air Pipe” for details on

alternate vent/flue pipe connection.

1. Remove the rubber plug/cap from the right-side drain port on

the front cover. Save the rubber plug/cap for later use.

2. Secure Hose A to the drain port on the front cover with a red

hose clamp.

3. Route Hose A to the rear right side panel grommet hole.

4. Remove the grommet from the front right side panel drain

hole.

5. Seal the hole in the grommet with the large end of the rubber

plug removed in Step 1.

6. Reinstall the grommet and rubber plug into the side panel

drain hole.

7. Cut ¹⁄₄" (6.4 mm) from the end of the drain port on the

externally mounted rubber elbow. Discard cut portion.

8. Insert Tube 1 into the rubber elbow drain port and secure with

a silver hose clamp.

NOTE: Angle tube toward drain trap.

9. Cut 17⁷⁄₈" (45.4 cm) from the long end of Hose B. Discard cut

portion.

10. Secure the remaining end of Hose B to the exposed end of

Tube 1 with a green hose clamp.

11. Route Hose B toward the right side panel grommet holes.

12. Insert the short end of one Tube 2 through the rear right side

panel grommet drain hole.

13. Secure Tube 2 to Hose A with a green hose clamp.

14. Insert the short end of the remaining Tube 2 into Hose B from

the rubber elbow and secure with a green hose clamp.

15. Ensure that the hoses and tubes maintain a downward slope

for proper drainage and are not kinked or binding.

A. Drain trap

B. Hose A

C. Hose B

D. Tube 2 (2)

E. Tube 1

F. Red hose cla mp (1)

G. Silver hose clamp (1)

H. Green hose clamps (3)

A. Right side panel

B. Rubber elbow

C. Rubber elbow drain

port

D. Red hose clamps

E. Tube 1

F. Hose B

G. Side panel

grommet holes

H.Tubes 2

I. Drain trap

J. Green hose clamps (3)

K. Hose A

L. Front cover drain port

IJKDL

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 51 52

Comments to this Manuals

No comments

Whirlpool WGFD295 Instruction Manual Page 20

Comments to this Manuals

Related products and manuals for Water heaters & boilers Whirlpool WGFD295