Whirlpool WGFD295 Instruction Manual download pdf (Page 23)

Horizontal Drain Trap Mounting—

Left or Right Side Panel

1. Position the drain trap against the side panel with the drain

tubes inserted into the trap.

NOTE: The trap may be orientated with the outlet facing

either the furnace’s top cover or base pan.

2. Secure the drain trap to the side panel at the dimples or

crosshairs located on either side of the grommet drain holes.

3. Confirm that the tubes reach the bottom of the drain trap and

that all of the hoses maintain a downward slope and are not

kinked or binding.

4. Attach the PVC drain line to the drain trap outlet with either a

90° elbow or coupling.

ELECTRICAL CONNECTIONS

Wiring Harness

The wiring harness is an integral part of this furnace. Field

alteration to comply with electrical codes should not be required.

Wires are color coded for identification purposes. Refer to the

wiring diagram for wire routings. If any of the original wire as

supplied with the furnace must be replaced, it must be replaced

with wiring material having a temperature rating of at least 105°C.

Any replacement wiring must be a copper conductor.

115-Volt Line Connections

Before proceeding with electrical connections, ensure that the

supply voltage, frequency and phase correspond to that specified

on the unit rating plate. Power supply to the furnace must be NEC

Class 1, and must comply with all applicable codes. The furnace

must be electrically grounded in accordance with local codes or, in

their absence, with the latest edition of The National Electric Code,

ANSI NFPA 70 and/or The Canadian Electric Code CSA C22.1.

Use a separate fused-branch electrical circuit containing properly

sized wire, and fuse or circuit breaker. The fuse or circuit breaker

must be sized in accordance with the maximum overcurrent

protection specified on the unit rating plate. An electrical

disconnect must be provided at the furnace location.

NOTE: Line polarity must be observed when making field

connections.

Connect hot, neutral and ground wires as shown in the wiring

diagram located on the unit’s blower door. For direct vent

applications, the cabinet opening to the junction box must be

sealed airtight using either an UL Listed/CSA approved bushing

such as Heyco Liquid Tight or by applying non-reactive UL

Listed/CSA approved sealant to bushing.

Line polarity must be observed when making field connections.

Line voltage connections can be made through either the right or

left side panel. The furnace is shipped configured for a right side

(left side for counterflows) electrical connection with the junction

box located inside the burner compartment.

To make electrical connections through the opposite side of the

furnace, the junction box must be relocated to the other side of

the burner compartment prior to making electrical connections.

To relocate the junction box, follow the steps shown in “Junction

Box Relocation.”

NOTE: Wire routing must not to interfere with circulator blower

operation, filter removal or routine maintenance.

Junction Box Relocation

Line voltage connections can be made through either the right or

left side panel. The furnace is shipped configured for a right side

electrical connection. To make electrical connections through the

opposite side of the furnace, the junction box must be relocated

to the left side prior to making electrical connections. To relocate

the junction box, perform the following steps.

1. Remove the burner compartment door.

2. Remove and save the 2 screws securing the junction box to

the side panel.

3. Relocate junction box and associated plugs and grommets to

opposite side panel.

4. Secure with screws removed in Step 2.

Goodman 70-A

To avoid the risk of electrical shock, wiring to

the unit must be polarized and grounded.

WARNING

HIGH VOLTAGE!

Goodman 115

HIGH VOLTAGE!

WARNING

To avoid personal injury or death due to

electrical shock, disconnect electrical

power before servicing or changing any

electrical wiring.

Goodman 59

Label all wires prior to disconnection when servicing

controls.

Wiring errors can cause improper

and

dangerous

operation. Verify proper operation after servicing.

CAUTION

Goodman 56

Edges of sheet metal holes may be sharp. Use gloves as

a precaution when removing hole plugs.

WARNING

Goodman 116

To prevent personal injury or death due to electric shock,

disconnect electrical power before installing or servicing

this unit.

WARNING

Goodman 60

HIGH VOLTAGE!

WARNING

To avoid the risk of injury, electrical shock

or death, the furnace must be electrically

grounded in accordance with local codes or

in their absence, with the latest edition of the

National Electric Code (NEC).

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 51 52

Comments to this Manuals

No comments

Whirlpool WGFD295 Instruction Manual Page 23

Comments to this Manuals

Related products and manuals for Water heaters & boilers Whirlpool WGFD295