Whirlpool HUI62T P Instruction for Use download pdf (Page 21)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

To switch the hob on, press and hold the button for

approximately one second.

The cooktop is switched On when a beep sound is

emmited and all the cooking zones displays show

the digit point.

When the cooktop is OFF, after 5 sec the control .

switches off the KEYLOCK LED to reduce the power

consumption.

As soon as we touch a key, the KEYLOCK LED goes

ON and we can continue to use the cooktop, unlocking

the keyboard.

Switching off the cooktop is signalled by 3 beep sound

Setting the Power Management

The cooktop maximum power limit is 7200W. This power

limit can be reduced by the user to 2800W, 3500W or

6000W.

The sequence to set a new Cooktop Power Limit is:

·During the first 30 seconds after plugging the applian-

·The Touch has to be unlocked and all Heaters Off

·Press at the same time Heater 1 and Heater 3 selection

keys

·Once this is done, a beep sounds and the actual Co-

oktop Power Limit will be shown in the heater displays.

For selecting a new Power Limit:

·With the (+) and (-) keys, the Power Limit is increased.

The selectable powers are: 2800W, 3500W, 6000W or

7200W. When the power is 7200W, if the [+] or [-] key is

touched the power changes to 2800W.

The sequence to finish recording the new Cooktop Po-

wer Limit is:

·Press at the same time Heater 1 and Heater 3 selection

keys

·Once this is done, new Cooktop Power Limit is recor-

ded and there is a system reset.

To finish without recording changes:

·If during 60 seconds there is no action, changes are not

recorded and there is a system reset.

Switching on the cooking zones

Each cooking zone is switched on and controlled using the

(-) and (+) POWER buttons, which at the same time

are used for power adjustment.

• To begin operating a cooking zone, set the desired

power level (between 0 and 9) using the (-) and (+)

POWER buttons

Press and hold the (-) POWER button to set the power

level immediately at “9”

Press and hold (+) and (-) POWER buttons simulta

neously to return to power level “0”

• Loud whistle: heard when two induction elements

of the same group function simultaneously at

maximum power and/or when the booster function

is set on the larger element while the other is auto-

adjusted. Noise is reduced by decreasing the power

level of the auto-adjusted induction element; pot

bottom layers made of different kinds of materials

are among the main causes of this noise.

• Fan noise: a fan is necessary to ensure the hob

functions correctly and to safeguard the electronic

unit from possible overheating. The fan functions at

maximum power when the large induction element is

at maximum power or when the booster function is on;

in all other cases, it works at average power depending

on the temperature detected. Furthermore, the fan may

continue to work even after switching the hob off, if the

temperature detected is high.

The types of noise listed above are due to induction

technology and are not necessarily operational faults.

! If the (-) or (+)button is pressed for an extended period

of time, the display scrolls quickly though the power

levels and timer minutes.

Initial Light Conditions

When power is initially applied to the Cooktop, the to-

uch control conducts a calibration process for the to-

uch keys, which requires a low level of ambient light in

the area of the touch keys.

If during this calibration process excessive ambient

lighting is detected the User Interface displays „FL”

(Infrared Ambient Light Error) and the control cali-

bration process is suspended. In order to rectify the

process any lighting that could effect the calibration

process should be switched off (e.g. halogen cooker

hood lighting). The error will disappear when satisfac-

tory ambient lighting is detected and the touch control

calibration procedure will now complete satisfactorily.

-The „FL” error can only be generated within approx 3s

of initial power being applied to the cooktop.

-We recommend that the user switches off all cooker

hood lighting and lighting directed towards the cook-

top when power is initially applied to the cooktop.

-After the touch control has conducted its initial cali-

bration process, (approx 3s) any cooker hood or other

lighting can be switched on as normal and will not af-

fect the operation of the touch control.

Switching on the hob

After connecting the hob to the electricity mains, the

touch pannel might be automatically locked. To un-

clock the pannel press and hold the Control Panel

Loock button .

Using the Ceramic Hob

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 35 36

Comments to this Manuals

No comments

Whirlpool HUI62T P Instruction for Use Page 21

Comments to this Manuals

Related products and manuals for Cookers Whirlpool HUI62T P