Whirlpool WGFD293 Instruction Manual download pdf (Page 37)

3. Knowing the furnace model, locate the high-stage cooling

airflow charts in the Specification Sheet applicable to your

model. Look up the cooling airflow determined in Step 2 and

find the required cooling speed and adjustment setting.

Example: A WGFM295070V4C furnace installed with a

2.5 ton air conditioning system. The airflow needed is

1,000 CFM. Looking at the cooling speed chart for

WGFM295070V4C, find the airflow closest to 1,000 CFM. A

cooling airflow of 990 CFM can be attained by setting the

cooling speed to B and the adjustment to “+” (plus).

4. Continuous fan speed is 30% of the furnace’s maximum

airflow capability.

Example: If the furnace’s maximum airflow capability is

2,000 CFM, the continuous fan speed will be

0.30 x 2,000 CFM = 600 CFM.

5. Locate the blower speed selection DIP switches on the

integrated control module. Select the desired cooling speed

tap by positioning DIP switches 1 and 2 appropriately. Select

the desired adjust tap by positioning DIP switches 3 and

4 appropriately. Refer to the following charts for DIP switch

positions and their corresponding taps. Verify CFM by noting

the number displayed on the dual 7-segment LED display.

Speed Taps—Adjust

Comfort Mode Profiles

The multispeed circulator blower also offers several custom On/

Off ramping profiles. These profiles may be used to enhance the

cooling performance and increase the comfort level. The ramping

profiles are selected using DIP switches 5 and 6. See the “Profile”

illustrations for DIP switch positions and their corresponding

taps. Verify CFM by noting the number displayed on the dual

7-segment LED display.

Profile A

■ Provides a 1 minute Off delay at 100% of the cooling demand

airflow.

Profile B

■ Ramps up to 50% of the full cooling demand airflow for

30 seconds.

■ The motor then ramps to 100% of the required airflow.

■ Provides a 1 minute Off delay at 100% of the cooling demand

airflow.

Profile C

■ Ramps up to 82% of the full cooling demand airflow for

approximately 7¹⁄₂ minutes.

■ The motor then ramps to 100% of the required airflow.

■ Provides a 1 minute Off delay at 100% of the cooling demand

airflow.

Speed Selection DIP Switches

Cool

Selection

Switches

Adjust

Selection

Switches

Profile

Selection

Switches

Heat

Selection

Switches

Tap12345678

A Off Off Off Off Off Off Off Off

B On Off On Off On Off On Off

C Off On Off On Off On Off On

D OnOnOnOnOnOnOnOn

Switch Bank: S3

DIP Switch Number

Cooling Tap

A Off Off

BOnOff

COffOn

D* On On

*Indicates factory setting

Switch Bank: S3

DIP Switch Number

Adjust Tap

Normal* Off Off

+10% Adjust On Off

-10% Adjust Off On

Normal On On

* Indicates factory setting

DIP Switch

Number

Ramping Profile Tap

A* Off Off

BOnOff

COffOn

DOnOn

* Indicates factory setting

Off

100% CFM

Cooling

Demand

100% CFM

1 min

Off

Off Off

50% CFM

100% CFM

1 min

Cooling Demand

¹⁄₂ min

82% CFM

100% CFM

1 min

Cooling Demand

7¹⁄₂ min

OffOff

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 51 52

Comments to this Manuals

No comments

Whirlpool WGFD293 Instruction Manual Page 37

Comments to this Manuals

Related products and manuals for Fireplaces Whirlpool WGFD293