Whirlpool WHES40 Troubleshooting Guide

TMModel WHES40How to install, operate andmaintain your DemandControlled Water SoftenerDo not return water softener to storeIf you have questions or co

Plan the InstallationInlet - Outlet Plumbing OptionsAlways install either a single bypass valve (provided) or, if desired, parts tk)r a 3 valve bypass

Installation InstructionsTurn Off Water Supply1. Close the main water supply valve, near the well pump or water meter.2. Open all faucets to drain all

Move the Water Softener into PlaceExcessive Weight HazardUse two or more people to move and installwater softener.Use two or more people to move and l

Assemble Inlet and Outlet PlumbingMeasure, cut, and loosely assemble pipe and fittings from the main water pipe to the inlet and outletports of the wa

Threaded pipe1. Apply pipe joint compound or Teflon ® tape to all male pipe threads.2. Tighten all threaded joints and make all solder connections.NOT

Test for LeaksTo prevent air pressure in the water softener and plumbing system, do the %llowing steps in order.1. Fully open two or more softened col

Program the Water SoftenerSET SALT LEVEL button DisplayTANK LIGHT buttonUP button/RECHARGE buttonGRAMTRESS TO SCHEDULEHOLD TO START_ECHARGE/ \PROGRAM

Set Water Hardness Number1. Press the O PROGRAM button once again to display aflashing 2_ and the w( rd HARDNESS .c3Hardness2 ppm iron x 5 = 10(times)

2. Check the brine tank and brinewell (black tube in salt storage tank) monthly. If hardening ispresent, pour small amounts of warm water on hardened

Customize Features/OptionsRechargeRecharge button is used to initiate an immediate recharge.Press and hold the O RECHARGE button until the words "

Table of ContentsWater Softener Safety ... 3Before You Start ...

Tank LightThe softener is equipped with a tank light for viewing the salt level in the brine tank. Push the tank lightbutton on the electronic control

Clean / Clear Water Iron RemovalThis fcature is beneficial on water supplies containing iron and/or high amounts of sediments (sand,silt, dirt, etc.).

Maximum Days Between RegenerationsThe water softener automatically controls regeneration frequency. This provides the greatest operatingefficiency, an

Routine MaintenanceRefilling With SaltLift the salt hole cover and check the salt storage level frequently. If"the conditioner uses all the saltb

Cleaning the Nozzle and VenturiA clean nozzle and venturi (see Figure 12) is a must for the conditioner to work properly. This smallwater softener cre

Troubleshooting GuideNeed help troubleshooting? (?all 1-866-986-3223, Monday - Friday, 8 am to 9 pm, EST.Tools Needed For Most Repairs: 5/16 Hex Drive

Automatic Electronic DiagnosticsThis water softener has a self-diagnostic function for the electrical system (except input power and/orwater meter). T

NOTE:5.6.Be sure water is in contact with the salt, and not separated by a salt bridge.., see"Breaking A Salt Bridge" section.While in this

NOTE: If water system pressure is low, an elevated drain hose may cause back pressure,stopping brine &aw.3. Again, press the O RECHARGE button to

Wiring SchematicBack of electronic boardDirect plug-in 118 ,, c .-- .--<transformer iii1 ,j12 , 124vacTanklightWarrantyo._NO Position switchNCWATER

Water Softener SafetyYour safety and the safety of others are very important.We have provided many important safety messages in this manual and on you

Softener Components4227269101112032 -_----_352835394O413O

Softener ComponentsKey Part No. DescriptionNo.1 7170296 O-Ring, 2-7/8" x 3-1/4"2 7170254 O-Ring, 13/16" x 1-1/16"3 7077870 Top Dis

Softener Componentsflow plugassemblyassembled279\11 1015J 1619303126 252432

Softener ComponentsKey Part No. DescriptionNo.1 7224087 Screw, #8-32 x 1" (2 req.)2 7250622 Motor (incl. 2 ea. of Key No. 1)3 7231393 Motor Plate

Notes34

Notes35

3/04

Inspect ShipmentThe parts required to assemble and install the water softener are included with the water softener.Copper tubes and groundclamp%Hose a

Water Softener DimensionsMODELWHES40,=_ 19"3-3/4"Lt c]FOUl- _18"CNOMINAL RESIN TANK SIZE10" DIA. X 40"A41-1/2"How a Wate

Water Conditioning InformationWater ConditioningWater conditioning is the treatment of four general conditions. These are:HardnessIronAciditySediments

2_3_4_Iron in water can cause stains on clothing and plumbing fixtures. It can negatively affcct the tasteof tk)od, drinking water, and other beverage

Installation RequirementsTools and Parts NeededAssemble the required tools before starting installation. Read and %llow tile instructious provided wit

Air Gap RequirementsA drain is needed for regeneration discharge water. A floor drain, close to the water softener, ispreferred. A laundry tub, standp