Whirlpool WHD3090GW Installation Manual download pdf (Page 11)

14. Remove garments promptly

after cycle is nished

Promptly remove garments after cycle has completed

to reduce wrinkling.

Wool

Air Dry

Refresh

Timed Dry

Bulky Bedding

Options

X-Dry

Dry

Damp

Dry

11. Select any additional options

After setting drying time or dryness level, the indicator light

above “Options” lights up. Turn the knob to select the desired

option(s). As you turn the knob, the option symbols above the

Options button will light up one at a time as you turn the knob.

Stop turning when the symbol of the desired option lights up.

Press the knob to conﬁrm your selection.

Not all options and settings are available with all program/

cycles. See “Program/Cycle Guide” for available options

and settings.

When the display indicates that the cycle has ﬁnished, touch

the Power button to turn off the dryer. Open the door and take

out your laundry.

To save energy, the dryer turns off automatically about

a quarter hour after the program/cycle ends.

If not turned off right after the program/cycle ends, the

dryer will tumble the laundry for about 10 minutes to prevent

wrinkling. The display shows an animation.

NOTE: If the Power button is touched and held, a countdown

will be displayed. At the end of the countdown, any errors will

be erased and the program/cycle will restart.

12. Touch Start/Pause button to begin

drying program/cycle

Touch the Start/Pause button to start the drying program/

cycle. To pause a program/cycle in progress, touch the Start/

Pause button once, then touch again to continue the program/

cycle. To cancel a program/cycle, touch the Power button.

13. Touch Power button to turn off

dryer after program/cycle ends

Adapting the dryer to water conductivity

The drying results are affected by the conductivity of the water

used during washing. If, by modifying the available dryness

levels (damp dry, dry, and extra dry), you are not satisﬁed with

the ﬁnal drying results, you can adapt the water conductivity

level. The dryer comes with preset level 3. Choose between

level 1 (most damp results) and 5 (most dry results).

1. Touch and hold the Program button. The

display will count down until the Conductivity

Adjustment symbol on the display ﬂashes

and the current setting is shown.

2. Turn the knob to adjust the level (1-2-3-4-5). Press the

knob to conﬁrm your selection.

NOTE: This new setting will affect all future cycles. If the

desired drying results are attained, water conductivity will

not require further adjustment.

Wool

Air Dry

Refresh

Timed Dry

Bulky/Bedding

X-Dry

Dry

Damp

Dry

Dryness

Level

10. If an automatic cycle was selected,

set dryness level

When you select an automatic cycle, the indicator light above

“Dryness Level” lights up. Turn the knob to select the desired

level. As you turn the knob, an indicator light will light up next

to the dryness levels to the right of the knob. Stop turning

when the indicator next to the desired level lights up. Press

the knob to conﬁrm your selection.

Options

Delay

Start

Timed

Dry

Dryness

Level

Program

3 Sec

Cycle

Signal

Control

Lock

Hold 3 Sec

Steam

X-Dry

Dry

Damp

Dry

Mixed

Heavy Duty

Normal

Synthetics

Delicates

Wool

Air Dry

Refresh

Timed Dry

Bulky/Bedding

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 67 68

Comments to this Manuals

No comments

Whirlpool WHD3090GW Installation Manual Page 11

Comments to this Manuals

Related products and manuals for Washer dryers Whirlpool WHD3090GW