Whirlpool 66161279 Use and Care Guide download pdf (Page 14)

Mode

1. Press MODE until you see the indicator light glow for the

desired setting.

2. Choose Cool, Eco (on some models), Overnight (on some

models) or Fan Only.

■ Cool—Cools the room. Fan Speed is set to Auto. Press

the up or down arrow button to adjust the temperature.

■ Eco (on some models)—Saves energy. The compressor

and fan runs until the set temperature is reached, and

then the compressor turns off. The fan runs an additional

minute before turning off. Automatically sets the fan

speed to Auto. Press the up or down arrow button to

adjust the temperature.

■ Overnight (8 hours) (on some models)—Automatically

raises the set temperature by 4ºF (2ºC). The Fan Speed is

set to Low. Press the up or down arrow button to adjust

the temperature. The set temperature increases 2ºF (1ºC)

per hour during the first 2 hours, and remains at this

temperature setting for the next 6 hours.

When Overnight mode ends, the air conditioner will go

into Cool mode and the thermostat setting will return to

the original Overnight mode temperature setting.

NOTE: The LEDs on the control panel will power down

10 seconds after Overnight mode is set. To reactivate the

LEDs and illuminate the control panel, touch any button

on the control panel or the remote control.

■ Fan Only—Only the fan runs. Press FAN SPEED to select

Low, Medium or High. The Bar LED shows 1 bar for Low,

2 bars for Medium and 3 bars for High fan speed. The

temperature display shows “1” for Low, “2” for Medium

and “3” for High fan speed. After 5 seconds, the display

shows the current room temperature.

NOTES:

■ Auto fan speed and Temperature cannot be selected

in Fan Only mode.

■ In Eco (on some models) and Cool modes, Auto fan

speed is selected automatically.

NOTE: Your model may differ from the one shown.

NOTE: After 5 seconds, display will show the current room

temperature.

Fan Speed

1. Press FAN SPEED until you see the Bar LED display for the

desired setting.

2. Choose High, Med, Low or Auto.

■ Low—Low cooling—1 bar and “1” shows in the

temperature display

■ Med—Normal cooling—2 bars and “2” shows in the

temperature display

■ High—Maximum cooling—3 bars and “3” shows in the

temperature display

■ Auto—Automatically controls the fan speed depending on

the current room temperature and temperature control

setting. “A” shows in the temperature display and 1, 2 or

3 bars display the current fan speed.

NOTES:

■ Auto fan speed and Temperature cannot be selected

in Fan Only mode.

■ In Eco (on some models) and Cool modes, Auto fan

speed is selected automatically.

■ In Overnight (on some models), Low fan speed is

selected automatically.

NOTE: After 5 seconds, the display will show the current room

temperature.

Temperature

■ Press the up arrow button to raise the temperature. Each time

you press or hold the up arrow button, the temperature will go

up 1ºF (1ºC) until it reaches 86°F (30°C).

NOTE: After 5 seconds, the display will show the current

room temperature.

■ Press the down arrow button to lower the temperature. Each

time you press or hold the down arrow button, the

temperature will go down 1ºF (1ºC) until it reaches 61°F

(16°C).

NOTE: After 5 seconds, the display will show the current

room temperature.

To change from Fahrenheit to Celsius

Press and hold the up and down arrow buttons to changed from

Fº to Cº. Release the buttons after Cº turns on.

Modes

Cool

Eco

Overnight

Fan Only

Min

AUTO

Fan Speed

ROOM: SET:

AUTO

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 59 60

Comments to this Manuals

No comments

Whirlpool 66161279 Use and Care Guide Page 14

Comments to this Manuals

Related products and manuals for Split-system air conditioners Whirlpool 66161279